1.1Radar measures load clearance
A 77 GHz radar unit on a bracket above the load sends frequency sweeps toward the material. A controller calculates the range from the frequency difference between the transmitted sweep and its return.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A 77 GHz radar unit on a bracket above the load sends frequency sweeps toward the material. A controller calculates the range from the frequency difference between the transmitted sweep and its return.
A sensor above the front of the body sends near-infrared pulses toward the load and measures the round-trip travel time. The controller converts that time to distance and subtracts the distance from the calibrated sensor height above the floor.
A steel bracket holds a 40 kHz transducer facing rearward below the tailgate. A frame-mounted controller measures the time between each transmitted burst and the returning echo to calculate the distance to an obstacle.
A bracket on the rear cab wall holds the transducer above the front of the bed and aims it down toward the load. A body-down switch enables sampling when the bed rests on its frame pads, and the controller converts each echo delay to a distance along the beam.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A wheeled cart carries a steel hopper on a rear hinge and uses a hydraulic cylinder to tilt it over a scrap bin. A sealed piezoelectric transducer and its drive electronics mount beneath the hopper floor near the discharge lip, with the transducer clamped to a welded coupling block. During unloading, the transducer sends ultrasonic vibration through the floor to help release fine ceramic particles as the scrap slides out.
A magnetostrictive transducer replaces the piezoelectric transducer in the ultrasonic assembly on a rear-hinged dump body. The assembly uses a wound drive coil around a laminated magnetostrictive core coupled through a steel horn to a welded sidewall pad. Body-mounted drive electronics supply alternating current at the assembly's longitudinal resonance, and the horn transfers the resulting ultrasonic vibration into the sidewall during discharge.
Three 24 kHz transducers mount beneath the rear half of a 2.4 m wide hinged dump body, with one on the centerline and the others 0.75 m to either side. Each transducer bolts to a separate coupling pad welded to the floor. A body-mounted controller energizes the transducers one at a time for 0.5 seconds each and repeats the sequence while the body is above 30 degrees from its lowered position.
A rotating dump body feeds a tailgate-mounted auger that meters road grit into a spinner. An ultrasonic transducer bolts to a welded pad on the underside of the body floor immediately upstream of the auger inlet. The spreader controller enables the transducer while the auger turns and switches it off when the auger stops. The transducer vibrates the floor at the inlet while the auger draws material from the body.
A pressure sensor connects to the lift cylinder's cap-end port, and a rotary position sensor measures dump body angle at the rear hinge. With the lift valve centered and the body stationary, the controller compares cylinder pressure with a stored empty-body pressure curve at the measured angle. If the pressure stays above the baseline by a calibrated margin for two seconds, the controller pulses a body-mounted ultrasonic transducer. The controller checks pressure between pulses and ends the sequence when the pressure returns within the margin or the pulse limit is reached.
A piezoelectric transducer clamps to a coupling pad beneath the hinged dump body, and a programmable driver mounts beside it. At startup, the driver sweeps a narrow band around the transducer's nominal resonance and measures voltage and current at the transducer terminals. The controller selects the conductance peak within that band and adjusts drive frequency in small steps to track it as the body unloads. The driver limits current during the sweep and during sustained operation.
A ceramic piezoelectric transducer emits an eight-cycle burst at 40 kHz. The controller blanks the receiver during transducer ring-down and measures the delay to the returning echo.
A bolted steel bracket on the upper front wall of the dump body holds a downward-facing transducer recessed behind a protective rim. A sealed connector joins the transducer to a harness clipped to the body, with a flexible loop at the rear hinge to accommodate tipping.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The ultrasonic generator is connected with a first ultrasonic transducer and a second ultrasonic transducer that emit ultrasonic of different frequencies, respectively.B · US 2012/0053493 A1 · abstract
Dump Truck Toy as claimed in claim 1 wherein an alternate version of said interaction means between said blocks and said microprocessor includes the use of light and dark colored graphics printed on said blocks and a plurality of photo sensors located under said socket portions in the base of said truck bed.A · US 2008/0166946 A1 · claim 6
An empty cell means only that no passage was reproduced there.
Although the above described patents disclose various methods of controlling a toy vehicle and may be effective, they do not allow a small child to direct a toy truck by placing directional controlling blocks into the truck bed of the toy.A · US 2008/0166946 A1 · ¶ 7
The primary object of the invention is to provide a motorized dump truck toy whose direction can be easily programmed by the user.A · US 2008/0166946 A1 · ¶ 8
The present Chinese Medicine therapy and Western Medicine therapy can only relieve the pain at most, neither of which can help the patients to cure the pain caused by above mentioned problem of vein athero-obstruction drastically.B · US 2012/0053493 A1 · ¶ 6
The objective of the present patent application is to provide an ultrasonic foot massage machine which can be used to treat the pain caused by the problem of vein ather-obstruction, aiming at the above mentioned drawbacks of the prior art.B · US 2012/0053493 A1 · ¶ 7
patent.fyi, US 2026/0356270 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356270/, SHA-256 86eaad73bc123599f647eaaef9c62465204f5bd481cca336b685c460292153f2