1.1Clamps on a smooth tube
Each accessory bolts to a two-piece collar that wraps around the tube. Two pinch bolts draw the collar halves together, creating friction that resists rotation and sliding along the tube.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Each accessory bolts to a two-piece collar that wraps around the tube. Two pinch bolts draw the collar halves together, creating friction that resists rotation and sliding along the tube.
A steel pedestal bolts through the deck into an underlying frame member. A saddle and cap grip the cross-bar at its midpoint, and the bar carries loads on either side of the pedestal as a cantilever.
Two square sockets bolt to frame members beneath the deck at fixed positions. A square shank on each foot drops into its socket, and a removable transverse pin retains the shank against uplift.
A flat flange welded to the end of the cross-bar bears against an upright plate on the foot. Four bolts pass through the flange and the upright plate to transfer load into the foot base.
A lever on the foot base turns an eccentric that advances a captive wedge between the cross-bar and one receiver wall. The wedge presses the bar against the opposite wall, and the lever passes over center to hold the wedge in position.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A slotted crossbar spans the perimeter rails of a wheeled nursery cart. A clamp plate secures each receiver foot to a side rail, and the crossbar ends lower through the open tops of the receivers. Two horizontal screws in one sidewall of each receiver enter threaded bosses in the corresponding bar end, and sliding nuts in the upper channel hold brackets for seedling trays.
Each open-top receiver carries two pull-ring indexing plungers threaded into horizontally spaced holes in one sidewall. Each crossbar end has a steel insert with two blind bores facing the plunger tips when the bar rests on the receiver floor. The installer retracts the tips to lower the bar and releases the rings to retain it, while the receiver floor and sidewalls carry the vertical and lateral loads.
Each mounting foot uses an injection-molded glass-filled nylon receiver in place of a metal receiver. Molded ribs connect the sidewalls to the base, and steel compression sleeves line two horizontally spaced holes in one sidewall. The crossbar end lowers through the open top, and screws pass through the sleeves into threaded bar-end inserts while the base transfers the vertical load to the perimeter rail.
A telescoping crossbar has an adjustable span of 1,100 to 1,450 mm, with at least 250 mm of overlap at maximum extension. A collar with two M8 clamp screws grips the inner section once both bar ends seat in their open-top feet on the perimeter rails. Each receiver has two horizontally spaced screws that thread into the bar end, and a separate upper mounting channel on each exposed bar section accepts cargo brackets.
A sliding cargo drawer travels on telescopic guides beneath a fixed deck that carries perimeter rails. Two crossbars sit in open-top receiver feet clamped to those rails, with two horizontally spaced screws per foot securing the bar ends. Channel nuts attach removable bins to the crossbars, and the drawer pulls out at the tailgate below the bins.
A strain-gauge load cell sits beneath each crossbar end on the floor of its open-top receiver. Two shoulder screws pass through vertically elongated holes in one sidewall of each foot and thread into the bar end, leaving enough clearance for the load cell to deflect under load. A controller reads a Hall sensor at each receiver to check the position of a magnet in the bar end, then displays the total supported load from the two calibrated cells when both ends are seated.
An extruded aluminum cross-bar has a continuous T-shaped channel in its upper face. A rectangular nut slides in from the bar end, and the channel lips retain the nut when an accessory screw is tightened.
A hollow aluminum cross-bar has one longitudinal mounting channel on its upper face and a second on its forward face. The upper channel supports an accessory platform, and the forward channel takes sliding nuts for adjustable tie-down rings.
Two upright walls bend up from a 4 mm steel base plate, and the space between them is open at the top. One wall has two 9 mm clearance holes for bolts that thread into inserts in the cross-bar end.
Each of the two cast aluminum feet has a base that bolts to two sliding clamp blocks captured in the perimeter rail. Upright cast walls form an open-top pocket, and one wall has two drilled holes that align with threaded bosses on the cross-bar end.
patent.fyi, US 2026/0356277 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356277/, SHA-256 8224c06b518d0b6165a370a3604fecb95eb6619067888bec8974705bef40d772