1.1Rear copper circuit routing
Leaded components mount on the front face and pass through unplated holes to solder lands on the rear face. Copper traces on the rear face distribute power and route sensor, lamp, and display signals.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Leaded components mount on the front face and pass through unplated holes to solder lands on the rear face. Copper traces on the rear face distribute power and route sensor, lamp, and display signals.
A spring-loaded cap travels 1.5 mm before actuating a sealed snap-action switch on the front face of the board. The controller registers a door request when the switch contacts remain closed for 20 ms.
A side-emitting diode on the rear face couples light into a molded clear polymer guide that wraps around the board edge. Extraction ridges direct the light through a translucent ring on the front of the housing.
A small stepper motor indexes a three-sided drum to show a door-open symbol, a wait symbol, or a blank face. A slotted optical interrupter detects the home position, and the controller counts motor steps to align the selected face with the aperture.
A narrow rectangular screen mounts along the upper edge and shows door status icons. The detection electrodes and light sources occupy the lower part of the same board, where a translucent strip marks the hand detection area.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A sealed housing bonds to the corridor side of a cleanroom door window. A rectangular display occupies the center of a printed circuit board, with a capacitive electrode and two indicator lights beside it. The electrode senses a gloved hand through the housing cover, and the board sends an entry request to the door interlock controller. The display shows the interlock state while the indicator lights signal when entry is available.
An infrared time-of-flight sensor replaces the capacitive hand sensor at the upper edge of the central display. Separate openings in an opaque bezel align with the emitter and receiver, and two visible indicator lights sit beside the display. The controller issues a door request when three consecutive distance readings fall between 30 and 80 millimeters.
A central display and adjacent capacitive electrodes occupy the front of the window-mounted board. Two light-emitting diodes on a separate daughterboard inject light into opposite ends of a molded polycarbonate light guide. The guide has two optically isolated segments that terminate in illuminated bars beside the display. The controller drives each diode independently so the bars indicate door availability and request acknowledgment.
An 85 by 45 millimeter printed circuit board carries a 40 by 22 millimeter display at its center. Two capacitive electrodes sit beside the short edges of the display, and two light sources sit along the lower edge behind separate clear windows. The controller samples the electrodes at 50 hertz and issues a request when either electrode detects a hand continuously for the configured dwell time of 120 to 400 milliseconds. Both lights pulse for 250 milliseconds after the request.
A window-mounted board carries a central display with hand sensors and indicator lights along its sides. A differential serial link connects the board to a powered wheelchair ramp controller. A touch sends a boarding request, and the ramp controller coordinates door opening and ramp deployment using its vehicle-stationary and door-open inputs. The display and lights follow the ramp controller's reported states and indicate when the ramp is ready.
A capacitive electrode sits beside the central display, and a reference electrode sits under the same cover behind a grounded patch on the bezel that shields it from approaching hands. The controller uses slow changes in the reference reading to compensate for drift in the sensing electrode and freezes its sensing baseline during a detected approach. A sustained rise above the compensated threshold registers a request, changes the displayed icon, and pulses a separate light below the display.
A 1.6 mm glass-fiber-reinforced epoxy laminate supports the components. Etched copper on the front face connects the sensor, light emitters, and display connector, and a solder mask covers the traces between pads.
Two copper electrodes on the front face of the board sense the electric field through a 2 mm polycarbonate cover. A capacitance controller tracks the baseline and signals a door request when a hand or finger produces a sustained increase above the set threshold.
Four surface-mount light-emitting diodes on the front face of the board feed a frosted polycarbonate ring. A constant-current driver holds each diode at 10 mA during illumination.
A 128 by 64 pixel liquid crystal screen mounts at the center of the board, with separate detection electrodes and light emitters positioned around it. A microcontroller sends stored bitmap images to the screen over a serial link as the door state changes.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The interior of the sign includes a printed circuit board 50 having a plurality of LED bulbs 46 mounted upon either side of the printed circuit board.A · US 2007/0113445 A1 · ¶ 23
When the user wants to change the state of the switch they touch the PDS and switch sensor will detect the touch and change the state of the switch as per the user programming.B · US 2013/0234841 A1 · ¶ 12
Our PDS includes a user programmable visual display element such as an Organic Light Emitting Diode (OLED) display panel. This display panel is user programmed with different graphics that represent the state of the associated relay.B · US 2013/0234841 A1 · ¶ 7
An empty cell means only that no passage was reproduced there.
A device is needed which provides enhanced illumination to alert the driver to even a greater degree than is present in existing signs.A · US 2007/0113445 A1 · ¶ 4
During road construction, it is common for a worker to hold a sign to warn of upcoming road construction.A · US 2007/0113445 A1 · ¶ 5
There remains, therefore, a need fur a programmable switch that is capable of duplicating the functionality of many other switches, while providing sufficient flexibility to convey its purpose to the user.B · US 2013/0234841 A1 · ¶ 6
Our PDS allows for graphics displayed on the visual display panel to be changed by the user even after the PDS has been installed into the target application.B · US 2013/0234841 A1 · ¶ 7
patent.fyi, US 2026/0356286 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356286/, SHA-256 c4461ca90f2cf269b3b3fac15ab152feefa8125be08f64f4f5b38f39f68b1050