1.1Equipment housing with integral seats
A one-piece cast housing has ribbed mounting seats with threaded steel inserts for the clamp screws. The ribs transfer clamp loads into the housing walls.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A one-piece cast housing has ribbed mounting seats with threaded steel inserts for the clamp screws. The ribs transfer clamp loads into the housing walls.
The pin passes through aligned holes in two bracket ears and a lug on the upper face of the bar. A cotter pin retains the cross pin axially, and the cross pin transfers transverse load in double shear.
A transverse screw draws two opposed jaws against machined flats near the top of the bar. Friction at the jaw faces resists vertical movement of the bracket.
The stud projects from the lower face of the bar and seats in an open notch in the bracket as the bracket pivots into position. The upper clamp holds the bracket in position, and the notch walls transfer lateral load into the stud by bearing.
A fixed shoe contacts the upper face of the flange, and a screw draws a movable shoe against its underside. The shoes grip the flange across its thickness and transfer bracket loads into the bar.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A steel rail bolts to the front of a packing bench and has an upper lip and a recessed lower pocket with a retaining shoulder. An upper hook on the bracket hangs over the lip, and a sliding lower clamp enters the pocket behind the shoulder. A hand screw holds the lower clamp in position, and a lamp arm bolts to the front face of the bracket.
A quarter turn cam fastener replaces the lower clamp. Its shaft passes through the bracket, and its offset steel pawl fits through the opening of the weight bar cavity in the release position. Once the upper clamp engages the lip, a quarter turn swings the pawl behind the cavity shoulder and draws the bracket against the bar.
An eccentric steel roller replaces the upper clamp and rotates between two bearing plates on the bracket. The roller sits behind the upper lip, and a fixed pad on the bracket contacts the front face of the bar below the lip. After the lower clamp seats in the cavity, a lever rotates the roller against the back of the lip to draw the pad against the bar. A spring-loaded pin engages a hole in one bearing plate to hold the lever in its closed position.
The bracket carries a fixed upper clamp and a lower clamp that travels vertically in a dovetail guide. Two cross holes in the guide, spaced 20 mm apart, set the vertical distance from the upper lip contact surface to the lower cavity contact surface at 80 mm or 100 mm. A removable 6 mm steel pin fixes the carriage at the selected height, and a threaded shoe on the lower clamp advances into the cavity.
The upper and lower clamps secure a plate bracket to the weight bar lip and cavity, and a pivoting work light bolts to the plate. A fused vehicle lighting circuit supplies the light through a sealed two-pin connector fixed to the bracket. A cushioned cable clip between the connector and the light takes strain from the lamp lead as the light pivots.
A fixed upper hook rests on the weight bar lip, and a geared motor drives a lead screw that translates the lower clamp into the cavity. A spring-loaded switch in the upper hook closes when the lip seats against the hook, and the controller accepts a close command only while the switch is closed. The controller stops the motor at a calibrated seating current and reports a fault if the current rises before the lower clamp reaches its engagement position sensor.
A press brake forms two return flanges along the sides of a low-carbon steel plate. The flanges stiffen the plate in bending, and holes in the plate locate the upper and lower clamp fasteners.
A steel hook reaches over the upper lip and bears against its rear face. A threaded draw screw pulls the hook toward the bracket and seats a fixed pad against the front face of the bar.
A pivoting jaw closes beneath the upper lip while a fixed saddle bears on the top of the lip. An eccentric cam moves the jaw as the handle rotates and holds it closed past center.
Two retractable steel shoes enter the cavity as the bracket seats against the bar. A screw pulls a tapered wedge between the shoes and presses them outward against opposing cavity walls.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The bracket 42 has a body 44, which may be formed from a metallic alloy, such as a zinc alloy, for example.B · US 2014/0026392 A1 · ¶ 23
A device for laterally positioning a work piece in a milling machine vise includes a clamp configured to engage a top longitudinal lip of a vise jaw via at least one clamp screw.A · US 2013/0270760 A1 · abstract
The leaf spring 74 expands within the second recess 40 thereby pressing the first recess 36 into engagement with the first retainer 70.B · US 2014/0026392 A1 · ¶ 28
An empty cell means only that no passage was reproduced there.
There is a long felt need in the market for a simple and reliable vise stop device which allows repetitious placement of a work piece along the longitudinal axis in relation to the cutting tool.A · US 2013/0270760 A1 · ¶ 5
The protrusion is configured to cantilever the stop pin substantially below the top lip resting face from the inner lip edge of the vise jaw and enable a milling clearance from the clamp to the work piece via the stop pin.A · US 2013/0270760 A1 · ¶ 6
patent.fyi, US 2026/0356299 A1, claim 1, first published 2026-11-19T23:14:26-05:00, https://patent.fyi/US20260356299/, SHA-256 765705294edd5fdd3d70e4ef06b1ecfab4929d1c5c9617c351527c848e79e064