1.1Upright operating lever
The lever extends vertically above a horizontal pin in its resting position. Pulling its upper end toward the cabin rotates the lever and draws a cable connected to the lock release arm.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The lever extends vertically above a horizontal pin in its resting position. Pulling its upper end toward the cabin rotates the lever and draws a cable connected to the lock release arm.
Two parallel guide rails constrain the release member to straight travel. Pulling the member draws the cable inner wire through its fixed sheath, and a compression spring returns the member after release.
A vertical pin supports the lever at its rear end so the front end sweeps toward the cabin when pulled. A cable nipple seated off center from the pin converts the sweep into cable travel at the door lock.
The recess gives the fingertips access to the back of the downward lip. Pulling the lip toward the cabin rotates the lever about its horizontal pin and tensions the lock release cable.
The pad slides into the door trim and drives a pushrod against one arm of a bell crank. The other arm draws the release cable, and a spring returns the pad when pressure is removed.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A horizontal lever mounts on the inner panel of a walk-in machinery cabinet door and pivots about a horizontal pin. The front end turns upward to form a gripping edge. Pulling the edge rotates a crank on the lever hub, which lifts a vertical rod to retract the spring-loaded latch bolt.
Two spring-steel leaf flexures replace the pin-and-bushing joint that supports the horizontal lever. The flexures mount on opposite sides of the lever root and align along a horizontal bend line. Pulling the upturned front edge bends the flexures and rotates a cable attachment tab on the lever root. The flexures return the lever when the pull is released, and a molded stop limits travel.
The horizontal lever places the upturned gripping edge 80 mm from the horizontal pivot axis. A cable drum with a 25 mm pitch radius rotates with the lever and draws the inner cable tangentially from a sheath anchored to the trim bracket. A stop limits rotation to 18 degrees, giving about 7.9 mm of cable travel at the latch release arm.
A horizontal lever with an upturned front gripping edge pulls a sheathed cable connected to the interior input arm of a rear door latch. A rotary child lock selector at the door edge shifts a coupling pin between the input arm and the latch release arm. In one selector position the pin couples the two arms, and in the other position the input arm moves independently. The exterior handle acts on a separate latch input.
A cam on the hub of the horizontal lever closes a switch during the initial pull at the upturned gripping edge. The switch signals the window controller to lower the frameless glass by 10 mm, measured by the regulator position sensor. A slot at the latch cable attachment provides initial free travel before continued lever rotation pulls the cable and releases the latch. A door-closed switch signals the controller to raise the glass after the door closes.
A magnet on the hub of the horizontal lever sweeps past a fixed Hall effect sensor as the user pulls the upturned gripping edge. A controller commands the latch actuator when the sensor indicates at least 7 degrees of lever rotation for 30 milliseconds. The controller accepts another pull after the lever returns below 3 degrees. A slotted mechanical link takes up its free travel during a longer pull and then drives the latch release arm directly.
The operating lever extends horizontally along the door trim at rest and pivots on a horizontal steel pin supported by two acetal bushings. Rotation draws the release cable, and a torsion spring around the pin returns the lever to its stop.
A glass-filled nylon lever has an integral front edge that rises 8 millimeters above the lever face and has a rounded crest. A pocket behind the raised edge gives the fingertips clearance to pull it toward the cabin and release the lock.
The front end of a stamped steel lever bends upward and terminates in a rolled hem. Pulling on the hem rotates the lever and draws the cable inner wire through its sheath.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The handle is operatively coupled to the latch release lever 133 such that actuation of the handle of the door handle assembly 114 causes the latch release lever 133 to rotate through a plane of rotation to unlatch the vehicle door assembly 20.A · US 2019/0284845 A1 · ¶ 26
The puller 24 can have one component 38 which grabs onto a corresponding “pulling” feature 36 of the first component 20 (referred to hereinafter simply as pulling lip 36), and retracts under a pulling force, with the first component 20, within a housing 40 which has a pushing feature 42 which remains in abutment with a corresponding feature of the second component 22 during the operation, with an amount of force sufficient to overcome the resisting friction force of the engagB · US 2022/0251973 A1 · ¶ 17
An empty cell means only that no passage was reproduced there.
Accordingly, a need exists for alternative blocking structures that can block unintended actuation of the door latch assemblies under certain side impact conditions.A · US 2019/0284845 A1 · ¶ 3
The latch release lever blocking structure is configured to deform in the vehicle longitudinal direction when acted upon by an impact force such that the catch arm moves into the plane of rotation of the latch release lever and the catch end catches the latch release lever at a location spaced from the bracket body to prevent the latch release lever from rotating to an unlatched position.A · US 2019/0284845 A1 · ¶ 4
In some cases, it is desired to provide the components with the capacity of being disassembled in a relatively simple manner.B · US 2022/0251973 A1 · ¶ 2
Fastening, by means of bolts, interference-fitting, or other, is typically considered to be of the disassemble-able type, whereas welding or brazing are typically not considered to be of the disassemble-able type.B · US 2022/0251973 A1 · ¶ 2
patent.fyi, US 2026/0356305 A1, claim 1, first published 2026-11-19T23:52:41-05:00, https://patent.fyi/US20260356305/, SHA-256 8eced0dca2d3157425e6fcd3819f3d1f0962b83063f0ff2467ce5bf652d9bff1