1.1Working tilt without folding
A worm gear drives a transverse pivot through a range of 0 to 15 degrees above horizontal. An angle sensor provides position feedback, and mechanical stops bound travel at both ends of the range.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A worm gear drives a transverse pivot through a range of 0 to 15 degrees above horizontal. An angle sensor provides position feedback, and mechanical stops bound travel at both ends of the range.
Three ultrasonic transducers on the backrest measure distance in separate sectors of the volume swept by the panel. The controller compares each distance with the clearance threshold for that sector and permits deployment when all three readings exceed their thresholds.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two 240 mm wide panels mount side by side on a 540 mm wide bench backrest with a 20 mm gap between them. Each panel has its own geared hinge drive and travels 90 degrees from the stowed position to its working stop. The controller enables each panel from the corresponding rear cushion occupancy sensor and opens it on a local button press. It folds each panel independently after the corresponding cushion reads vacant for three seconds.
The panel controller connects to the powered recline controller for the seat that carries the panel. A linear position sensor on the recline actuator identifies a range in which the open panel clears the rear passenger's knees. The panel controller allows deployment on request when the rear cushion is occupied and the recline actuator is within that range. A recline request that crosses the range boundary pauses seat motion while the panel folds, and a stow switch releases the recline interlock.
A recessed pedal at the rear passenger's seat base contains a force sensor and is reachable from a seated position. The controller samples the pedal and seat cushion sensors and registers a command when an occupied seat produces at least 30 N at the pedal for 800 milliseconds. Successive commands alternate between opening and folding the seatback panel, with a pedal release required between commands. A contact strip on the panel edge stops motion and causes a short reversal if the panel encounters an obstruction.
A piezoresistive pressure mat beneath the rear seat cushion measures load across four sensing zones. The monitoring module reports an occupied state when the summed load remains above a calibrated threshold for 500 milliseconds.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Actuator(s) 206 can cause the ramp 200 to deploy from the stowed position at controlled rate(s), to, through, and past the vertical, and ultimately to a horizontal or other desired state.B · US 11,572,084 B2 · ¶ 67
Thus, the vehicle OPD system, method, and algorithm described herein ultimately detect and utilize occupant posture information, α, α′, β, and/or φ, rather than simple seat information and can be used in combination with other seat and vehicle sensors to provide both occupant posture and position in a vehicle such that safety and restraint systems can be fine-tuned.A · US 11,161,430 B2 · ¶ 28
Such a bus can comprise a body supported by a frame and housing a plurality of passenger seats; at least one passenger access door configured to enable passenger access through at least one side of the body; and a plurality of vehicle exterior condition sensors, the plurality of vehicle exterior condition sensors comprising: at least one passenger presence detector; at least one vehicle navigation sensor; at least one steering controller; at least one speed controller; at leaB · US 11,572,084 B2 · ¶ 7
An empty cell means only that no passage was reproduced there.
Thus, what are needed in the art are improved seat-related vehicle occupant comfort, safety, and design features.A · US 11,161,430 B2 · ¶ 2
Thus, the vehicle occupant posture detection (OPD) system, method, and algorithm described herein provide enhanced occupant comfort and safety with an economical number of seat sensors.A · US 11,161,430 B2 · ¶ 4
However, concerns persist with respect to passenger accessibility and ride quality, and other aspects of passenger comfort and safety.B · US 11,572,084 B2 · ¶ 4
In various further aspects and embodiments, such buses and controllers can be configured to automatically and/or semi-automatically deploy charging interfaces, for charging of batteries and other energy storage systems, and to automatically level and/or otherwise orient the buses in a condition suitable for charging at a charging station.B · US 11,572,084 B2 · ¶ 8
patent.fyi, US 2026/0356309 A1, claim 1, first published 2026-11-19T23:52:41-05:00, https://patent.fyi/US20260356309/, SHA-256 79db2a341c503b9d26ce586f277a2d25602fe81364495bb14a8c3218770747e4