patent.fyi
Applications  /  US 2026/0356334
United States Patent Application Publication

US 2026/0356334 A1

Published
Nov 12, 2026
Filed
Nov 27, 2023
Earliest date on the face
Dec 7, 2022
Classification
B60T 8/26
First published here
Nov 19, 2026

Generated automatically. Not reviewed by a person. Not legal advice or an opinion.

Section 1 · machine-generated

What if?

Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.

No entries.

Section 2 · machine-generated

Variations

Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.

Other field of use

Braking for an overhead crane trolley

A hydraulic disc brake and an inverter-driven induction motor act on the same trolley wheel through its drive shaft. A speed controller converts the difference between commanded and measured trolley speed into a wheel braking torque request. The hydraulic brake follows a low-pass-filtered torque request, and the motor supplies the difference between the total request and the pressure-based estimate of friction torque. The drive dissipates generated energy in a braking resistor.

Component substitution

Electromagnetic powder brake for fast correction

An electromagnetic powder brake replaces the high-dynamic control actuator on a low-speed industrial vehicle. The powder brake rotor is keyed to the wheel shaft, its housing is fixed to the axle carrier, and a hydraulic caliper acts on a disc on the same shaft. A current regulator uses a calibrated current-to-torque table to command the powder brake from the difference between requested wheel torque and estimated caliper torque. The controller clips the powder brake request to its temperature-dependent torque limit and transfers sustained demand to the caliper.

Parameter or scale variation

Independent correction at four driven wheels

A four-wheel vehicle pairs a hydraulic caliper and an independently controlled electric motor at each wheel. Each wheel controller filters its local torque request with a 250 ms time constant for the caliper and estimates friction torque from measured line pressure. Every 5 ms, the controller commands the local motor to supply the remaining braking torque, limited to 300 N·m at the wheel. The hydraulic target increases when sustained demand reaches the motor limit.

Combination with existing systems

Torque blending with regenerative energy storage

A hydraulic caliper and an inverter-driven traction motor act on the same wheel, and the inverter feeds recovered energy to a battery through a direct-current bus. The battery management controller supplies a charge power limit based on cell temperature, voltage, and state of charge. The brake controller combines that limit with motor speed and an inverter torque map to cap the regenerative share of the wheel torque request. The hydraulic caliper supplies the sustained share and takes up any reduction in available regenerative torque.

Torque blending with wheel slip control

An independently driven wheel carries a hydraulic caliper and an electric motor connected through a fixed reduction gear. An anti-lock controller estimates braking slip from wheel speed and a vehicle speed estimate derived from the other wheels and a longitudinal accelerometer. As slip rises above the controller target, the motor quickly reduces its braking contribution while the hydraulic modulator releases pressure when the estimated friction torque alone exceeds the reduced wheel torque request. As slip recovers, the motor restores braking torque within its available limit while the caliper pressure ramps up.

Automated or data-driven variant

Load sensing for axle torque distribution

A two-axle vehicle uses suspension deflection sensors to estimate static axle loads and an inertial sensor to measure longitudinal deceleration. A controller calculates dynamic axle loads from those measurements, wheelbase, and center-of-mass height, then allocates the total braking request between the axles in proportion to their estimated loads. On each axle, hydraulic calipers track the filtered torque allocation and an axle motor supplies the difference between the current allocation and estimated friction torque. The controller clips motor torque to the available regenerative limit and adds any sustained shortfall to the caliper request.

Cite aspatent.fyi, US 2026/0356334 A1, claim 1, first published 2026-11-19T23:52:41-05:00, https://patent.fyi/US20260356334/, SHA-256 513e155f3c6f2ffd672ae47532fc0a3e486e225c8700c6752470a42b59d2ec28
First published
Permanent addresshttps://patent.fyi/US20260356334/
Content fingerprint (SHA-256)513e155f3c6f2ffd672ae47532fc0a3e486e225c8700c6752470a42b59d2ec28
Methodv2026-11-18.2 · automated, not reviewed by a person
Correctionscorrections@patent.fyi