1.1Air actuated wheel brakes
A pedal valve meters reservoir air to service chambers that push the brake pads against the discs. Separate spring chambers apply the brakes for parking and emergency operation when their release pressure vents.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A pedal valve meters reservoir air to service chambers that push the brake pads against the discs. Separate spring chambers apply the brakes for parking and emergency operation when their release pressure vents.
A fused cable connects the brake controller and wheel actuators directly to the battery that also supplies the other vehicle loads. A contactor disconnects the auxiliary loads when battery voltage reaches a threshold set to retain enough energy for a brake application.
An electric reset motor compresses a spring at each brake, and an energized latch holds it in that position. An emergency command or a loss of holding power releases the latch, allowing the spring to drive a thrust plate against the pads.
A pump charges a gas-backed hydraulic accumulator, and a check valve retains pressure when the pump stops. A spring-return valve opens when de-energized and routes fluid through a pressure regulator to separate pistons at the wheel brakes.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An indoor rail-guided transfer cart carries electromechanical disc calipers on its front and rear wheelsets. A charger connects the cart's traction supply to a dedicated brake battery, and a separate feed connects the battery to both caliper drives. A brake controller commands proportional clamping for service stops and sustained clamping for parking. A hardwired undervoltage input triggers an emergency application on both wheelsets using the brake battery when the traction supply drops below its operating threshold.
An electrically driven hydraulic pump and modulating valve block operate hydraulic wheel calipers in place of motor-driven calipers. The valve block meters pressure for service braking, and a motor-driven cable applies the rear parking brakes. An onboard charger maintains a dedicated battery that feeds the pump, valve block and brake controller through a fused reserve circuit. When the main supply drops below its operating threshold, the reserve circuit powers the pump and valves to build and regulate pressure during the emergency stop.
A three-axle carrier uses six electromechanical calipers rated for a 48 V brake bus, with a dedicated reserve connected through a regulated converter. If each caliper draws 12 A for 0.8 s during emergency application, simultaneous operation requires 72 A and approximately 2.8 kJ at the brake bus. The controller permits dispatch when the reserve can deliver at least 4.0 kJ at the bus under the measured temperature and load. The reserve rating also covers controller draw and any clamp corrections required by the emergency stop.
A brake controller shares deceleration requests with a traction inverter that reports available regenerative torque. The controller subtracts delivered regenerative torque from the service brake request and commands the remaining torque through the electromechanical wheel brakes. The wheel brakes provide parking force and receive electrical power from a dedicated reserve during an emergency application. When the traction supply fails, the controller sets regenerative torque to zero in its allocation and commands the wheel brakes to meet the emergency deceleration request.
Voltage, current and temperature sensors monitor the dedicated brake energy store, and a switched resistor applies a brief test load while the vehicle is stationary. Software estimates internal resistance from the voltage drop and current step, then combines the estimate with temperature and charge measurements to predict the minimum terminal voltage during an emergency application. The controller inhibits drive enable when the predicted voltage falls below the brake electronics' operating limit. The onboard charger replenishes the charge used by the test.
A dedicated brake reserve powers the electromechanical calipers, wheel speed sensors, longitudinal accelerometer and brake controller during an emergency stop. The controller estimates vehicle speed from the fastest wheel and the integrated longitudinal acceleration, then calculates slip for each wheel. It reduces local clamp force when slip exceeds a calibrated upper threshold and reapplies force below a lower threshold. The reserve energy budget includes the motor movements needed for slip control through the stop.
At standstill, a shift actuator engages a steel pawl with a toothed wheel on the transmission output shaft. The engaged pawl holds the driven axle through the final drive until the actuator withdraws it.
The pack charges in an external docking station and slides into an isolated brake power module. If the normal actuator feed loses voltage, a transfer relay disconnects that feed and connects the pack to the brake controller and actuator supply.
A brushless motor turns a ball screw through a reduction gear, and the screw advances a piston against the brake pads. A clamp-force sensor provides feedback during service and emergency braking, and a mechanical latch holds the screw at the parking position.
A dedicated brake battery uses a series stack of lithium iron phosphate cells in a sealed enclosure. Its battery management circuit monitors cell voltage and temperature and balances the cells during charging.
A fused branch from the vehicle power bus supplies an isolated direct-current converter that charges the brake storage pack. The converter limits charge current and blocks reverse current from the pack into the vehicle bus.
The brake controller sets a minimum reserve charge from the energy required for one emergency application at the lowest specified operating temperature, with allowance for cell aging and conversion losses. The controller tracks pack charge and switches the brake actuators to reserve power if the normal supply falls below its operating threshold.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A typical drum-in-hat type of disc brake assembly includes a hydraulically or pneumatically actuated disc service brake and a mechanically actuated drum-in-hat parking and emergency brake.A · US 7,490,702 B1 · ¶ 3
The nominal brake command typically is associated with the normal pedal-based brake function or other traditional downgrade modes. The park brake command typically is associated with a hand brake lever or the like for providing continuous braking when the vehicle is parked and, in the event of a severe fault with the nominal brake command, may be employed to provided extreme emergency braking when the vehicle is in motion.B · US 7,850,254 B2 · ¶ 2
An empty cell means only that no passage was reproduced there.
In particular, the embodiments described herein relate to an improved structure for a parking brake actuator for use in a vehicle drum-in-hat disc brake assembly.A · US 7,490,702 B1 · ¶ 1
Such frictional engagement causes slowing or stopping of the rotational movement of the rotor and, therefore, the wheel of the vehicle in a controlled manner.A · US 7,490,702 B1 · ¶ 5
Nonetheless, there remains a possibility that the nominal system may fail.B · US 7,850,254 B2 · ¶ 4
Accordingly, there is a need for a brake-by-wire brake system having a nominal brake command system independent of the park brake command system such that the park brake command system may be used for extreme emergency braking.B · US 7,850,254 B2 · ¶ 5
patent.fyi, US 2026/0356335 A1, claim 1, first published 2026-11-19T23:52:41-05:00, https://patent.fyi/US20260356335/, SHA-256 45d019b3a9c356ee08643173832ae0ae76903bdde81e1f543f30229b350ccc72