1.1Single outlet with external tee
A single bore in the chamber wall feeds a tee in the external brake line. One branch runs to the isolation valve and the other runs to the accumulator charging valve.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A single bore in the chamber wall feeds a tee in the external brake line. One branch runs to the isolation valve and the other runs to the accumulator charging valve.
An electric motor rotates a ball screw that advances a piston in a fluid-filled cylinder. The piston displaces fluid into the wheel circuit, and a pressure sensor supplies feedback for motor control. The motor retracts the piston to release pressure.
At each wheel, an electric motor drives a reduction gear and a screw that presses the brake pads against the rotor. The controller adjusts motor torque using clamp force feedback and reduces clamp force when wheel speed indicates excessive slip.
The pedal-operated cylinder feeds one set of pistons, and the emergency hydraulic circuit feeds a second set through separate passages. Both sets act on the same pads, while their sealed bores prevent fluid transfer between the circuits.
The pump draws fluid from the reservoir and delivers it through a check valve to the accumulator inlet. A pressure sensor starts and stops the pump at lower and upper pressure thresholds, and the check valve holds the stored pressure when the pump stops.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A two-outlet hydraulic supply chamber feeds a service brake valve manifold through an isolation valve and a hydropneumatic accumulator through a charging valve. A separate accumulator outlet feeds a pressure-applied emergency caliper on the hoist drum through a normally open activation valve that is held closed by a solenoid. An independent drum speed switch de-energizes the solenoid at the overspeed threshold, and stored fluid flows through a pressure-reducing valve to apply the emergency caliper.
A spring-loaded piston accumulator stores hydraulic energy for automatic emergency braking. The first chamber outlet feeds the service brake circuit through an isolation valve, and the second chamber outlet feeds the accumulator inlet through a charging valve. Fluid entering the accumulator displaces a sealed piston against a preloaded coil spring. When the activation valve opens, the spring drives the piston back and sends fluid through the separate accumulator outlet to the brake circuit.
A normally closed proportional spool valve controls flow from the accumulator outlet to the wheel brake supply manifold. The first chamber outlet connects to the manifold through an isolation valve, and the second chamber outlet connects to the accumulator inlet through a charging valve. During an emergency stop, a controller compares manifold pressure with a rising pressure command and adjusts spool current to meter accumulator flow. A separate return valve connects the manifold to the reservoir when the controller reduces the pressure command.
The first chamber outlet feeds the service brake manifold through an isolation valve, and the second outlet charges a 0.20 L nitrogen bladder accumulator through a charging valve. The accumulator has separate inlet and outlet passages into a common fluid cavity, and an activation valve connects the outlet to the brake manifold. The nitrogen precharge is 80 bar and the hydraulic operating range is 100 to 160 bar, with all pressures specified as gauge values. An ideal isothermal gas estimate gives approximately 60 mL of fluid delivery as accumulator pressure falls from 160 to 100 bar.
A vehicle with an electric traction motor uses regenerative torque and hydraulic friction brakes to meet a common deceleration command. The first hydraulic chamber outlet supplies the friction brake manifold through an isolation valve, and the second outlet charges an accumulator whose separate outlet supplies the same manifold through an activation valve. During automatic emergency braking, the brake controller subtracts the reported regenerative torque from the requested wheel braking torque and converts the remainder to a hydraulic pressure command. The controller meters the activation valve using manifold pressure feedback and increases the friction brake command as regenerative torque falls.
The first chamber outlet feeds the service brake manifold through an isolation valve, and the second outlet feeds the accumulator inlet through a charging valve. A pressure transducer and a temperature sensor at the accumulator measure the state of the stored charge while the activation valve at the separate outlet is closed. When the service brake is idle and measured pressure falls below a temperature-adjusted lower threshold, the controller starts an electric pump supplying the chamber and opens the charging valve. At the upper threshold, the controller closes the charging valve and stops the pump, then monitors pressure decay to detect loss of stored charge.
Two radial passages in an aluminum cylinder housing open into the same pressure chamber beyond the piston seal at rest. Each passage terminates in a separate threaded port with a conical seat for a brake line fitting.
A sealed floating piston separates precharged nitrogen from brake fluid in a steel cylinder. Separate inlet and outlet drillings in the fluid end cap open into the same cavity, where incoming fluid compresses the nitrogen and expanding nitrogen drives discharge.
A spring holds a solenoid-operated poppet off its seat so fluid passes between the first chamber outlet and the wheel circuit during pedal braking. Energizing the solenoid seats the poppet and blocks flow back toward the chamber during automatic emergency braking.
A normally closed proportional solenoid valve connects the accumulator outlet to the wheel supply line. A controller adjusts coil current to vary the metering opening and uses a downstream pressure sensor to track the requested brake pressure.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The oil accumulator forces the oil with the bladder to the hydraulic cylinder. The oil accumulator connects to the hydraulic cylinder, and the hydraulic cylinder connects to the at least one brake leg.B · US 10,343,655 B1 · ¶ 18
Each side of the circuit includes a proportional valve to achieve the trailer braking function and a shutoff valve to stop the proportional valve from working unintentionally.A · US 7,517,026 B1 · ¶ 5
An emergency braking system for vehicles, consisting essentially of: A) a hydraulic unit assembly having an oil reservoir containing a first predetermined quantity of oil, said hydraulic unit assembly further having an electric motor and an electrovalve, said oil reservoir being connected to said electric motor;B · US 10,343,655 B1 · claim 1
After accumulator 142 has been filled with enough oil, closure valve 148 prevents oil accumulator 142 from emptying when is not operating. Closure valve 148 therefore maintains oil pressure in oil accumulator 142 until a pressure sensor within pedal switch actuator 150 sends a signal to release the oil to hydraulic cylinder 162, and thereafter, permitting oil accumulator 142 to be filled again with oil.B · US 10,343,655 B1 · ¶ 39
An empty cell means only that no passage was reproduced there.
There is a need for redundant electro-hydraulic and electro-pneumatic control circuits for trailer brakes in a by-wire brake system.A · US 7,517,026 B1 · ¶ 3
Accordingly, an object of this invention is to provide a control circuit for electro-hydraulic and electro-pneumatic by-wire trailer brakes which can function even if one of the internal components fails.A · US 7,517,026 B1 · ¶ 4
patent.fyi, US 2026/0356336 A1, claim 1, first published 2026-11-19T23:52:41-05:00, https://patent.fyi/US20260356336/, SHA-256 883622b717605946afe6a81a775c7f851808197a20f7708d532299f5a4da412f