patent.fyi
Applications  /  US 2026/0356406
United States Patent Application Publication

US 2026/0356406 A1

Published
Nov 12, 2026
Filed
Jul 18, 2023
Earliest date on the face
Sep 8, 2022
Classification
B61L 27/53
First published here
Nov 20, 2026

Generated automatically. Not reviewed by a person. Not legal advice or an opinion.

Section 1 · machine-generated

What if?

Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.

1.1Wayside measurement controller

What ifWhat if a wayside processor obtains the initial friction coefficient and evaluates measurements from a passing vehicle?
Claim language“in a respective one of at least one rail vehicle”

The wayside processor retrieves the initial coefficient from a table indexed by track segment. Vehicle electronics apply the test force under local traction limits and send time-stamped axle speeds and force readings to the wayside processor for evaluation.

1.3Fixed axle braking pulse

What ifWhat if the controller commands a fixed braking torque for a short interval while measuring the individual axle speeds?
Claim language“applying a gradually increasing traction force”

The traction inverter applies a preset regenerative braking torque to the selected axle and releases it when the axle speed drops below the reference by a set margin or the pulse timer expires. When a speed departure occurs, the controller estimates the wheel–rail friction coefficient from the axle torque, angular deceleration, wheel radius and normal load.

1.4Ground speed radar reference

What ifWhat if the controller compares the selected axle’s tread speed with ground speed measured by a downward-facing radar sensor?
Claim language“an average rotational speed of said axles”

The controller multiplies the selected axle’s angular speed by its calibrated rolling radius and aligns that reading with the time-stamped radar speed. It triggers the friction calculation when the absolute difference exceeds a threshold in metres per second.

1.6Repeat measurement agreement

What ifWhat if the controller accepts a measured friction value based on agreement among repeated measurements on the same segment?
Claim language“lies within an acceptance interval from the basic parameter”

The controller collects three estimates from separate traction ramps on the same segment. It accepts the latest estimate when the range of the three coefficients is at most 0.03.

1.7Weighted friction update

What ifWhat if the controller calculates the validated friction value from a weighted blend of the initial value and the accepted measurement?
Claim language“assigning the validated value equal to the measured value”

After the acceptance check passes, the controller multiplies the accepted measurement by 0.75 and the initial segment value by 0.25. It adds the two terms and passes the result to the transmitter.

Section 2 · machine-generated

Variations

Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.

Other field of use

Adhesion reporting for mine haulage

A powered mine haulage vehicle stores an initial adhesion coefficient for each track block identified by a passive track marker. A controller increases traction on one axle and compares its rotational speed with the mean speed of the remaining axles. When the absolute speed difference crosses a threshold, the controller divides the driven axle's estimated tractive force by its measured normal load and accepts the result if it falls within the block's acceptance interval. The vehicle sends the accepted coefficient and block identifier to receivers on other haulage vehicles.

Component substitution

Ground speed reference from doppler radar

A downward-facing Doppler radar supplies ground speed in place of the mean rotational speed of the reference axles. The controller multiplies the test axle's measured rotational speed by its calibrated rolling radius and compares the resulting wheel speed with radar ground speed during a traction ramp. At the first threshold crossing, the controller estimates adhesion from wheel torque, rolling radius and axle normal load. It compares the estimate with the segment's acceptance interval and transmits the accepted value to other vehicles.

Parameter or scale variation

Six axle measurement with speed gating

A six-axle inspection vehicle samples all axle speeds at 200 Hz and permits a traction ramp between 10 and 20 km/h on designated test segments. The controller ramps one axle's tractive force at 1 kN/s and uses the mean speed of the other five axles as its reference. An absolute speed difference greater than 0.5 rad/s for five consecutive samples triggers an adhesion estimate using the force and normal load recorded at the first crossing. The transmitter reports the estimate when it falls within 0.03 of the segment's initial coefficient.

Combination with existing systems

Adhesion updates for rail sanding control

A supplier vehicle carries a measurement controller, and receiving vehicles connect their friction message receivers to onboard sanding controllers. The supplier runs the traction ramp with its sanders inactive and broadcasts an accepted coefficient with the track segment identifier and measurement time. Each receiver matches the segment to its onboard route map and stores the report until a configured expiry time. An unexpired report below a configured adhesion threshold selects the low-adhesion sanding profile for that segment, and the sanding controller meters sand in response to local wheel slip.

Automated or data-driven variant

Segment baselines from recent measurements

A software service stores accepted adhesion reports indexed by track segment, direction and timestamp. Before a test run, the onboard controller retrieves the latest seven reports for the segment and direction and uses their median as the initial coefficient. The controller increases traction on one axle, detects slip from its speed difference against the other axles and compares the resulting adhesion estimate with an interval centered on the median. An accepted estimate is sent to receiving vehicles and added to the service's report history.

Load corrected adhesion from suspension sensors

Pressure transducers on the air springs, a bogie accelerometer and a traction torque sensor feed synchronized samples to the measurement controller. A calibrated suspension model converts spring pressures and longitudinal acceleration into an estimate of the test axle's normal load during the traction ramp. When the axle's speed differs from the reference axle mean by more than the threshold, the controller subtracts the torque used to accelerate the wheelset from the measured wheelset torque and divides the remainder by rolling radius and estimated normal load. The transmitter sends the resulting coefficient and segment identifier when the coefficient falls within the acceptance interval.

Specific version of a part

Onboard segment friction table

The measurement controller uses a track map and the vehicle’s current route position to identify the occupied segment. It reads the initial friction coefficient from an onboard flash table keyed by segment identifier.

Encoder feedback during torque ramp

Magnetic encoders generate pulses for each axle, and a common timer provides timestamps for calculating rotational speeds. The traction inverter increases the selected axle’s torque command in equal increments at 20-millisecond intervals.

Timed axle speed comparison

Every 10 milliseconds, the controller calculates the arithmetic mean of the three reference axle speeds and subtracts it from the selected axle speed. It triggers the friction calculation when the magnitude of the difference exceeds 0.5 radians per second for three consecutive samples.

Binary radio broadcast packet

The onboard transmitter broadcasts a binary packet containing a segment identifier, a timestamp and the validated coefficient encoded as an integer in units of 0.001. Each receiving vehicle checks the packet checksum and stores the coefficient under the segment identifier.

Cite aspatent.fyi, US 2026/0356406 A1, claim 1, first published 2026-11-20T01:05:31-05:00, https://patent.fyi/US20260356406/, SHA-256 a214cee3e2999e999c1c5e1d37b4358e53732421262bfedf3136f597d1edc55b
First published
Permanent addresshttps://patent.fyi/US20260356406/
Content fingerprint (SHA-256)a214cee3e2999e999c1c5e1d37b4358e53732421262bfedf3136f597d1edc55b
Methodv2026-11-18.2 · automated, not reviewed by a person
Correctionscorrections@patent.fyi