1.1Suspended fabric load carrier
A woven sling clips directly to the housings of two side modules, each supported by a pair of wheels. The fabric carries the load in tension, and the module housings transfer the sling forces to the wheel bearings.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A woven sling clips directly to the housings of two side modules, each supported by a pair of wheels. The fabric carries the load in tension, and the module housings transfer the sling forces to the wheel bearings.
Two geared motors drive rubber-tired wheels on opposite sides of the frame, and two ball supports carry the remaining load. A speed difference turns the device, and equal speeds in opposite directions rotate it about the midpoint between the drive wheels.
Four wheels carry free-spinning tread rollers set at 45 degrees to the wheel axles, with opposite roller orientations on adjacent wheels. Motor speed and direction determine how the four traction forces combine to move the frame forward, sideways, or in rotation.
A caster fork drives a sealed rotary viscous damper through its swivel shaft. Fluid shear resists fast swivel motion and dissipates oscillation energy, while the damper permits continuous rotation.
A magnet ring on the swivel shaft interacts with a stationary magnet ring across an air gap, creating a stable alignment at the straight-ahead heading. Ground forces acting through the caster offset overcome the centering torque during a turn, and the shaft remains free to make a full revolution.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse harvest cart carries a pair of front swivel wheels beneath a tubular tray frame. Each wheel fork has a radial steel arm that turns between two upright tabs welded to a frame crossmember. The tabs limit fork rotation in either direction so the wheels stay clear of the tray supports during turns at aisle ends.
A steel plate fixed beneath the frame has an arcuate slot centered on the wheel fork's vertical swivel axis. A shoulder bolt on the fork carries a hardened roller that projects into the slot and travels along it as the fork turns. The rounded ends of the slot stop the roller and set the two steering limits.
Two stainless steel wire ropes run from separate frame anchors to opposite ends of a crossarm fixed to the swivel fork. Each rope passes between its anchors through a shallow slack loop retained by a guide beneath the frame. Turning the fork takes up slack in one rope while adding slack to the other, and the taut rope stops further rotation in that direction. Threaded terminals at the frame anchors set each steering limit independently.
A long platform cart carries two 160 mm swivel wheels at the front and two 160 mm swivel wheels at the rear. A radial arm on each fork sweeps between two adjustable stop screws threaded into brackets on the frame. With the fork arms pointing straight ahead, the front screws are set for 45 degrees of travel to either side and the rear screws are set for 20 degrees to either side. Jam nuts hold the screws in position after adjustment.
A towable platform cart has two front swivel wheels connected by steering arms and a transverse tie rod. A pivoting towbar drives the tie rod through a drag link, turning both front wheel forks as the towbar moves from side to side. A stop pin on each fork contacts one of two blocks bolted beneath the frame at the ends of steering travel. The blocks are positioned so the stop pins engage before the tie rod or drag link reaches its articulation limit.
A swivel fork carries a radial arm that travels between two frame-mounted stop blocks with fixed outer limits at 50 degrees to either side of straight ahead. Each block carries an inner stop pin that a solenoid extends into the arm's path at 15 degrees from center. A controller reads ground speed from a wheel encoder and extends both pins above 1.2 metres per second when a swivel angle sensor reports that the arm is within 10 degrees of center. The controller retracts both pins when speed falls below 0.8 metres per second, restoring the full steering range.
Rectangular steel tubes form two side rails connected by welded crossmembers. Steel mounting plates welded beneath the rails distribute wheel loads into the frame.
A fork mounts beneath the frame on a vertical stem carried by a radial bushing and a thrust bearing. The wheel axle trails the stem axis by 30 millimeters, so the wheel aligns with the direction of travel as the frame moves.
A steel pin on the swivel fork travels in a curved slot centered on the directing axis in a plate fixed to the frame. The two slot ends contact the pin at 45 degrees on either side of straight ahead.
Two stop screws thread into a bracket fixed to the frame, and a tab on the swivel fork contacts one screw at each end of travel. Turning the screws adjusts the left and right limits independently, and jam nuts hold each setting.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As best illustrated in FIGS. 1 through 7, the motorized stroller assembly 10 generally comprises a carriage frame 12.B · US 2022/0212706 A1 · ¶ 20
The angled rear portion 34 includes a bottom surface which supports a swivel caster wheel assembly 36.A · US 2013/0257003 A1 · ¶ 28
In such an arrangement, if provided, the void can be larger than the actuator portion to permit rotational movement of the actuator portion throughout a desired range of motion of the rear wheel 29 about the pivot axis 44. Further, the void, acting on the actuator portion, could function as a limit stop arrangement to define maximum rotational positions of the rear wheel 29 about the pivot axis 44.A · US 2013/0257003 A1 · ¶ 39
An empty cell means only that no passage was reproduced there.
What is needed is an improved and new scooter and brake design that provides alternative range of movement to the user.A · US 2013/0257003 A1 · ¶ 8
Preferred embodiments of the scooter also generally include at least one swivel caster wheel located on the rear of the scooter, allowing the user to cause the scooter to travel in a non-linear movement or ride the scooter using a side to side motion similar to the rear movement of a swivel caster board.A · US 2013/0257003 A1 · ¶ 9
The disclosure relates to stroller devices and more particularly pertains to a new stroller device for supporting a parent or other person while a person is transporting a child in the stroller device.B · US 2022/0212706 A1 · ¶ 6
Moreover, the stroller device may include a drive assembly to move the stroller device over a ground surface.B · US 2022/0212706 A1 · ¶ 6
patent.fyi, US 2026/0356413 A1, claim 1, first published 2026-11-20T01:05:31-05:00, https://patent.fyi/US20260356413/, SHA-256 749e3656545d522bdaa6e308cbe34d4ff853c960473564d7a925277e9b2d00b2