1.1Steering on a ring bearing
The inner bearing race bolts to an annular vehicle bracket, and the outer race bolts to the rotary housing. A stationary magnetic sensor reads a multipole ring on the outer race to measure steering rotation.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The inner bearing race bolts to an annular vehicle bracket, and the outer race bolts to the rotary housing. A stationary magnetic sensor reads a multipole ring on the outer race to measure steering rotation.
Two parallel linear guides constrain the housing to lateral travel, and opposed springs return it to center. A linear position sensor measures signed displacement, which the controller maps to a commanded road-wheel angle.
The yoke straddles the outer rim of the rotary housing and bolts to the vehicle mounting unit. Its forward crossmember supports the fixed housing through a flange at the front opening, with clearance between the flange and the rotating rim.
A stamped steel bracket bolts to the instrument-panel crossbeam and holds the display at a fixed viewing angle. A wiring harness supplies power and carries vehicle speed, selected gear, and status data to the display.
A lower crossbar on the rotary housing carries a left grip and a right grip. The driver turns the crossbar through the grips to command steering, while separate spring-return triggers report acceleration and braking demands.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stationary center shaft attaches to the operator console of a battery-powered baggage tug and supports a fixed display housing. Two hand controls attach to opposite sides of a rotary housing that turns around the shaft. A rotary encoder supplies the steering angle to the axle steering actuator, and grip-mounted levers command traction torque and service braking. The fixed display shows travel direction, battery charge, and trailer coupling status.
An open aluminum yoke replaces the rotary housing and carries a grip at each end. A crossed roller bearing joins the yoke to the stationary center shaft, with its inner ring clamped to a shaft shoulder and its outer ring bolted to the yoke. The fixed display housing bolts to the exposed end of the shaft and sits between the grips. A magnetic angle sensor measures yoke rotation for steering, and sensors in the grips generate acceleration and braking commands.
Each hand control uses two spring-steel flexure levers in place of hinged levers to sense acceleration and braking requests. One flexure sits under the thumb and the other under the fingers, and each carries a strain-gauge bridge near its fixed end. Both grips attach to the rotary housing, and a separate shaft angle sensor measures steering. A signal conditioner converts flexure strain to force and maps it to acceleration or braking demand after applying a calibrated force threshold.
The rotary housing carries two grips whose centerlines are 260 mm apart, with the fixed display centered between them. Mechanical stops limit housing travel to 25 degrees on either side of center. A magnetic angle sensor measures the housing position, and the steering controller maps the 50-degree input span linearly to a road-wheel steering range of 35 degrees to either side. Grip-mounted levers provide separate acceleration and braking inputs.
An angle sensor measures rotation of the grip housing relative to the stationary center shaft. The steering controller reads vehicle speed and interpolates between calibration curves that map housing angle to road-wheel angle. At full housing travel, the curves command 35 degrees of road-wheel angle at or below 5 km/h and 8 degrees at or above 40 km/h. The fixed display shows the measured road-wheel angle, and the grip levers supply separate acceleration and braking signals.
Two spaced sealed ball bearings support the rotary housing on a stationary steel through-shaft. A shaft shoulder and retaining nut locate the bearing inner races axially, and machined seats in the housing retain the outer races.
A die-cast aluminum housing seats against a shoulder on the center shaft inside the rotary housing. A keyed bore sets the angular position, and an axial bolt clamps the housing against the shoulder.
A backlit liquid crystal panel sits behind a bonded cover lens in a bezel fastened to the fixed housing at four points. A closed-cell foam gasket cushions the display assembly and limits dust entry around the bezel.
A grip on each side of the display bolts at its root to the rotary housing and projects toward the driver. The driver turns the housing through the grips and squeezes separate spring-return triggers for acceleration and braking. A magnet on each trigger moves past a Hall sensor to measure trigger travel.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A scooter having a foot platform defining forward and rear ends, front and rear wheels at the forward and rear ends of the foot platform, and comprising; a swingable bearing at the forward end of the platform; a steering column mounting sleeve attached to the swingable bearing; a front wheel drive shaft in said steering column mounting sleeve and being telescopically slidable therethrough; a hub extension at the lower end of the steering column mounting sleeve for mounting thA · US 2012/0267871 A1 · claim 1
The light-emitting elements 3 are preferably arranged behind a light-transmissive layer 4 that is embedded in the steering wheel rim and through which light is output.B · US 11,345,383 B2 · ¶ 52
The invention further provides such a scooter wherein the hand bars comprise a transverse portion coupled to the steering column mounting sleeve, and rotatable relative thereto, and two hand holding portions displaced at angles to said central portion, and moveable through downward and upward arcs, and linkage connected to the front wheel drive shaft whereby to reciprocate said front wheel drive shaft through said steering column mounting sleeve.A · US 2012/0267871 A1 · ¶ 9
An empty cell means only that no passage was reproduced there.
It may make it difficult to keep the balance on the scooter and may make the riding unstable, or even unsafe.A · US 2012/0267871 A1 · ¶ 3
This will make it easier to keep balance on the scooter and centre the weight, so that the scooter does not tip over.A · US 2012/0267871 A1 · ¶ 4
Therefore, it makes sense to display the end of an automation section so as to prepare the driver for once again taking over control of the vehicle.B · US 11,345,383 B2 · ¶ 7
It should be ensured that the driver takes over control of the vehicle before the end of the automation section.B · US 11,345,383 B2 · ¶ 8
patent.fyi, US 2026/0356418 A1, claim 1, first published 2026-11-20T01:05:31-05:00, https://patent.fyi/US20260356418/, SHA-256 3baff4ea30dfeecabb75100ee609cd7d34fdda6d92b540d2f277dab6ca180de1