1.1Mechanical steering linkage
A steering shaft turns a pinion that moves a rack connected to both front wheels by tie rods. A torque sensor measures driver effort, and an electric motor applies assist torque through a reduction gear.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A steering shaft turns a pinion that moves a rack connected to both front wheels by tie rods. A torque sensor measures driver effort, and an electric motor applies assist torque through a reduction gear.
A steering controller reads the handwheel angle and commands a proportional valve fed by a hydraulic accumulator. The valve meters fluid to either side of a double-acting cylinder, and a rack position sensor provides feedback as the cylinder moves the tie rods.
A fork pivots in a steering head at the front of a three-wheel chassis. An electric motor turns the fork through a reduction gear in response to the handwheel angle, and a sensor measures the fork angle for feedback.
Fixed-length toe links set the rear wheel alignment, and independent drive motors apply longitudinal force at the two rear tires. A yaw controller adjusts the difference between the motor torque commands to turn the vehicle about its vertical axis.
An open bevel-gear differential transmits approximately equal torque to the rear half-shafts while allowing the wheels to rotate at different speeds. A rear steering actuator changes both rear wheel angles, generating lateral tire forces that produce the requested yaw moment.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A battery-powered tow tractor uses a front steer-by-wire rack, a rear steering actuator, and independently controlled rear traction motors. When the controller detects a front steering fault, it disconnects the front motor from its inverter and shorts the motor phases through a motor-side switch. During a controlled stop, the controller uses rear steering to track the commanded path and biases torque between the rear motors to damp yaw measured by an inertial sensor.
An electrohydraulic cylinder moves the rear steering rack in place of a rear electric steering motor. A position sensor on the cylinder closes the rear wheel angle loop through an electrically controlled proportional valve, and a hydraulic accumulator supplies pressure during the fault transition. When the controller detects a front steering fault, it shorts the front motor phases, commands rear wheel angle through the valve, and adjusts the rear drive torque split to correct yaw error.
A three-pole isolation contactor sits between the front steering inverter and the motor, and a second three-pole contactor connects the motor terminals to a common shorting bus. On detection of a front steering fault, the controller inhibits inverter switching, opens the isolation contactor, and verifies its open position through auxiliary contacts before closing the shorting contactor. The controller then coordinates rear wheel angle and rear drive torque split using measured front wheel angle and yaw rate.
Following detection of a front steering fault, the controller shorts the front motor phases and runs the rear steering and torque allocation loop every 10 milliseconds. The controller limits rear wheel angle to 5 degrees in either direction at speeds up to 10 kilometers per hour and to 1 degree at speeds of 60 kilometers per hour and above, with linear interpolation between those speeds. It converts the yaw moment request remaining after rear steering into a left-right rear drive torque difference bounded by the available wheel torque.
The fallback steering controller receives wheel slip status and rear wheel torque limits from the traction control system. When a front steering fault triggers the motor phase short, the fallback controller requests a rear wheel angle and a left-right drive torque difference. The traction controller clips each rear wheel torque command to its current slip limit and reports the applied torques, which the fallback controller uses to update the rear steering request.
An extended Kalman filter uses wheel speeds, yaw rate, lateral acceleration, and independent front and rear rack position measurements to estimate vehicle speed and sideslip. After the controller detects a front steering fault and shorts the motor phases, it uses the measured front wheel angle as an input to a vehicle model. A constrained optimizer uses the model and state estimates to select rear wheel angle and rear drive torque split while tracking the requested yaw rate and respecting actuator travel and wheel torque limits.
A three-phase permanent-magnet motor drives a recirculating ball nut through a toothed belt. The rotating nut translates the steering rack, and a linear position sensor measures rack travel for closed-loop control.
An electric motor rotates a lead screw that moves a transverse slider connected to both rear toe links. A position sensor measures slider travel, and the controller converts the requested rear wheel angle into a travel setpoint.
Each rear wheel receives drive torque from its own electric motor through a fixed reduction gear. The controller apportions the requested axle torque between the motors to generate a yaw moment and limits each torque command according to measured wheel slip.
When the fault monitor requests a phase short, the gate driver turns off the three upper inverter switches and turns on the three lower switches, tying the motor phase terminals together. Motor rotation induces winding currents that oppose rack motion through the steering transmission.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The front road wheel actuator system (FRWAS) 14 is configured to receive command signals from the controller system 16 and converts the command signals to a steered wheel motion. In this embodiment, this may include a mechanism that connects both the front steered wheel by means of tie rods to a rack and pinion device, where an electric motor imparts the rotary motion to the pinion, which in turn moves the rack.A · US 6,929,086 B1 · ¶ 41
The angle from HWA 10 is sent to the RWA 20 which performs position control to control rack travel to guide the roadwheel.B · US 2019/0389508 A1 · ¶ 23
Additionally, the rear road wheel actuator continues to receive control signals from the controller and rotate the rear road wheels accordingly.A · US 6,929,086 B1 · ¶ 29
If the front system experiences a fault and the rear steer-by-wire system is still able to function, then the mechanical backup clutch will engage, thereby placing the system into a manual steering mode. However, the rear wheels may be controlled to assist the driver and provide greater maneuverability of the vehicle.A · US 6,929,086 B1 · ¶ 47
An empty cell means only that no passage was reproduced there.
Front and Rear wheel steering provides increased vehicle maneuverability relative to front wheel steering only vehicles.A · US 6,929,086 B1 · ¶ 9
However, manufacturers have been challenged in implementing rear wheel steering with other vehicle features.A · US 6,929,086 B1 · ¶ 9
In the SbW system, it is desirable to provide a notification to the driver in response to the deviation caused by rack force disturbances due to road surface variation (banking, pothole, road texture) or tire/wheel related phenomenon.B · US 2019/0389508 A1 · ¶ 3
The handwheel control module further modifies the input command using the modification signal, the modification providing a notification corresponding to the deviation to the driver.B · US 2019/0389508 A1 · ¶ 6
patent.fyi, US 2026/0356421 A1, claim 1, first published 2026-11-20T01:05:32-05:00, https://patent.fyi/US20260356421/, SHA-256 ce81aced8901751ffb087ce9dfc27f1e9ada3466a608aaf556758630957db622