1.1Use a driver override paddle
A momentary paddle sends a discrete input to the controller. While the paddle is held, the controller blocks new corrections and ramps any active steering command to zero.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A momentary paddle sends a discrete input to the controller. While the paddle is held, the controller blocks new corrections and ramps any active steering command to zero.
While correction is inactive, the controller compares the indicated turn direction with the side of the predicted lane crossing. It inhibits correction when the directions match and otherwise enables correction when the predicted time to the lane boundary falls below a calibrated limit.
A steering-angle sensor supplies samples from which the controller calculates signed wheel speed. The controller ramps the correction torque to zero when wheel speed exceeds 15 degrees per second in the direction opposite to the correction torque for 150 milliseconds.
A forward camera estimates the vehicle's lateral offset and heading error relative to the lane centerline. The controller ramps correction torque to zero when both the absolute offset and the absolute heading error stay below 0.25 meters and 1.5 degrees, respectively, for 200 milliseconds.
The controller reads one calibration value for the inactive state and for both steering directions during active correction. It uses that value to block a start or end an active correction when the measured operator torque magnitude reaches the cutoff.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A manually steered agricultural tractor uses a forward camera to locate the crop rows on either side of its travel corridor. A steering controller estimates the tractor's lateral position and heading from the row geometry and commands an electric steering actuator to apply corrective torque toward the corridor center. A steering shaft torque sensor supplies operator torque for three distinct limits, with one limit for blocking activation and two limits for ending active correction according to whether the operator torque opposes or reinforces the corrective torque.
Two magnetic angle encoders measure shaft rotation at opposite ends of a calibrated torsion bar in the steering column. The controller subtracts the lower shaft angle from the upper shaft angle, removes the calibrated zero offset, and multiplies the resulting twist by the torsion bar stiffness to estimate signed operator torque. The controller uses the estimated magnitude with a standby limit before activation and with one of two distinct active limits selected by comparing the estimate's sign with the corrective torque command.
An electronically controlled proportional hydraulic valve meters fluid to either chamber of a double-acting cylinder connected to the steering linkage. The controller converts its corrective torque request to a pressure difference using cylinder piston area and the effective steering arm length at the measured steering angle, then regulates valve current using pressure feedback from both chambers. A steering column torque sensor supplies the signed operator torque used to block activation at the standby limit and to end correction at either of two distinct active limits selected by torque direction. When correction ends, the controller ramps the auxiliary pressure request to zero and returns the valve to its neutral position while the manual steering path remains available.
A controller samples signed operator torque at 200 Hz and applies a five-sample median filter before comparing its magnitude with the selected limit. The standby limit is 2.0 N·m, the active limit for opposing torque is 1.2 N·m, and the active limit for reinforcing torque is 3.0 N·m. A sample at or above the standby limit blocks activation, and eight consecutive samples at or above the same active limit trigger termination. On termination, the controller ramps corrective torque to zero over 100 ms.
A continuous lane centering controller and a departure suppression controller share an electric power steering actuator through a torque arbiter. The arbiter selects the centering command during normal tracking and selects the departure suppression command when predicted boundary crossing triggers intervention and operator torque is below the standby limit. During intervention, the arbiter selects one of two distinct active torque limits by comparing operator torque direction with the departure suppression command. Reaching the selected limit ends departure suppression and holds both automated torque requests at zero until operator torque stays below the standby limit for a calibrated recovery interval.
The controller records absolute steering shaft torque during manual lane tracking in a rolling buffer for each vehicle speed band. Between interventions, it computes the 95th percentile for the current speed band and clamps the result to a calibrated standby range. It derives a lower active limit for opposing torque and a higher active limit for reinforcing torque by applying fixed offsets to the standby value. The controller freezes the resulting three values when correction begins and uses the applicable active limit until the correction ends.
The controller samples the steering torque sensor every 10 milliseconds and applies a low-pass filter to the signal. When the filtered torque magnitude reaches the selected threshold, the controller blocks entry into correction if correction is inactive and clears the correction command if correction is active.
During active correction, the controller compares the signs of the measured operator torque and the commanded correction torque. When the signs differ, the controller selects a 2.0 newton-meter threshold and ends correction when the operator torque magnitude reaches it.
The controller stores three values in nonvolatile memory. It selects 2.5 newton-meters while correction is inactive, 1.5 newton-meters while active with opposing operator torque, and 3.5 newton-meters while active with same-direction operator torque.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The control unit is configured to, when a determination is made that the vehicle travels obliquely to the lane based on the position of the vehicle detected by the vehicle position detection device and a determination is made that the steering torque detected by the steering torque detection device is equal to or greater than a reference steering torque, start prohibition of issuing of the warning and prohibition of steering of the steering wheel.A · US 2022/0204082 A1 · ¶ 9
For example, Japanese Unexamined Patent Application Publication No. 2011-168194 (JP 2011-168194 A) describes that lane departure suppression control is restricted when a steering speed equal to or higher than a reference value, a steering torque equal to or larger than a reference value, and/or a steering torque change amount equal to or larger than a reference value are/is detected.B · US 2024/0067267 A1 · ¶ 5
An empty cell means only that no passage was reproduced there.
Therefore, in the lane departure prevention device in the related art, it is not possible to determine whether or not the driver intends to cause the vehicle to depart from the lane and to regulate steering of the steering wheel or the warning before the risk that the vehicle departs from the lane is detected, and it is not possible to prevent the driver from feeling anxiety due to the warning.A · US 2022/0204082 A1 · ¶ 6
The control unit is configured to, when a determination is made that there is a risk that the vehicle departs from the lane based on the position of the vehicle detected by the vehicle position detection device, perform at least one of issuing a warning by the warning device and steering of the steering wheel, for preventing the vehicle from departing from the lane.A · US 2022/0204082 A1 · ¶ 8
Thus, the lane departure cannot effectively be suppressed to cause the vehicle to travel in compliance with the law.B · US 2024/0067267 A1 · ¶ 6
The present disclosure provides a lane departure suppression device improved so that lane departure suppression control is not executed in a situation in which the lane departure suppression control should be restricted, and lane departure can be suppressed in a situation in which the lane departure is prohibited by the law.B · US 2024/0067267 A1 · ¶ 7
patent.fyi, US 2026/0356425 A1, claim 1, first published 2026-11-20T01:05:32-05:00, https://patent.fyi/US20260356425/, SHA-256 6aeadeb09cb52cc1c98387506bdf41c08483b8fe10459fa29cce2e1ca8895fea