1.1Single alloy aluminum base
Shallow stamped ribs stiffen the plate against transverse bending. Loads from the face sheets pass through the plate to mounting flanges along its edges.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Shallow stamped ribs stiffen the plate against transverse bending. Loads from the face sheets pass through the plate to mounting flanges along its edges.
Two heated polypropylene blanks fuse around their perimeter and at molded contact pads during twin-sheet thermoforming. The separated walls provide bending depth, and the contact pads transfer shear between them.
Bolts pass through drilled holes in the sheet and through compression sleeves at the base mounting points. Wide washers spread the clamp load on the sheet, and the sleeves limit compression of the base as the nuts tighten.
A toughened epoxy bonds the steel panel to the composite base over broad contact areas. The steel spreads localized contact loads into the base and provides a surface that resists abrasion.
The sheet slides into two inward-facing channels that overlap its edge margins and restrain lift. A removable end stop blocks withdrawal, and bearing pads on the base support inward loads.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A glass fiber composite base carries a continuous glass fiber organo sheet bonded to each face. Side brackets mount the panel above the return belt at an aggregate transfer point, with its upper face pitched toward a collection chute. The upper sheet takes impacts from falling aggregate, and the lower sheet carries tensile load as the panel bends between brackets.
A stamped aluminum sheet takes the place of the lower organo sheet on a road vehicle underbody panel. An epoxy film adhesive bonds the aluminum sheet to the lower face of a glass fiber composite base, and a compatible thermoplastic film bonds a glass fiber organo sheet to the upper face. The aluminum sheet faces the road and deforms locally under stone impact while the bonded base distributes the load.
A 600 mm by 400 mm underbody panel uses a 2.0 mm glass fiber reinforced polypropylene base, a 3.0 mm road-facing organo sheet, and a 2.5 mm vehicle-facing organo sheet. Both sheets use continuous glass fibers in a polypropylene matrix and fuse to opposite faces of the base in a heated compression mold. The thicker road-facing sheet provides additional material at the surface exposed to abrasion and stone impact.
Two glass fiber organo sheets bond to opposite faces of a composite base that spans the underside of a vehicle battery enclosure. Quarter-turn studs sit in flanged sleeves at the panel perimeter and engage spring receptacles on enclosure crossmembers. The sleeves transfer fastening loads across the laminate thickness, and the studs remain captive in the panel when it drops clear for enclosure service.
A glass fiber composite base carries an organo sheet bonded to each face, and foil strain gauges bond to the vehicle-facing sheet between the mounting points. A sealed signal conditioner samples the gauges and records strain peaks that exceed a threshold set during panel impact testing. The recorded peak and gauge location identify the part of the panel for inspection after an underbody strike.
A robot transfers two infrared-heated glass fiber organo sheets into a matched die and positions a preheated thermoplastic composite base between them. An infrared camera measures the bond-facing surface of each sheet before transfer, and a controller adjusts individual heater zones to bring each surface into the bonding temperature window for the matrix resin. The die presses the sheets against opposite faces of the base and maintains pressure until the bonded stack cools below the matrix solidification temperature.
Injection molding forms a base from long-glass-fiber polypropylene pellets. The tool forms broad bonding lands on two opposite sides and ribs between the lands on one side.
The first organo sheet contains woven continuous glass fabric consolidated in a polypropylene matrix. A heated platen softens the sheet surface and the polypropylene-rich bonding lands on the first side of the base, and pressure holds them together during cooling.
The second organo sheet contains woven continuous carbon fiber consolidated in a polyamide matrix. A toughened epoxy bonds the prepared sheet surface to the second side of the composite base, and glass spacer beads control the adhesive thickness during cure.
A preheated continuous-glass-fabric organo sheet with a polypropylene matrix sits against one wall of the mold. Molten glass-filled polypropylene forms the base against the sheet and fuses with its matrix at the second side as the assembly consolidates under pressure.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In a further embodiment, on the side of the organo-sheet opposite the injection molding side of the adapter a through-molding cavity is provided in the molding die, which only by through-molding of the reinforcing element or organo-sheet in the region of the reinforcing element can be filled with the material of the plastic matrix, so that the degree of filling can be used as quality feature for the connection to be produced.A · US 2016/0136870 A1 · ¶ 19
To produce the positive connection between the adapter 8 and the organo-sheet 2, a through-molding cavity is provided in the molding die on the side of the organo-sheet 2 opposite the injection molding side of the adapter 8, which can only be filled with the material of the plastic matrix of the adapter 8 by through-molding the reinforcing element or organo-sheet 2 in the region of the reinforcing element.A · US 2016/0136870 A1 · ¶ 83
Subsequently, first of all that portion of the organo sheet 2 that is located in the injection-molded component 1 is formed into the inlay or consolidated, and subsequently, the inlay is overmolded to produce the injection-molded component 1.B · US 2017/0157819 A1 · ¶ 41
An empty cell means only that no passage was reproduced there.
Organo-sheets can be cut to size like metal sheets and be provided with apertures, but are lighter than metal sheets and at the same time have a high surface stiffness and strength.A · US 2016/0136870 A1 · ¶ 4
Structural components for motor vehicles, for example door elements such as door modules, assembly carriers, door inner panels and door outer panels, seat elements such as seat pan and backrest, but also fenders, flaps and hoods, bumpers and the like thereby can be manufactured in a lightweight construction, and distinct weight reductions thereby can be achieved with easier processing at the same time.A · US 2016/0136870 A1 · ¶ 4
The advantages of a thermoplastic matrix reside in the hot formability of the semifinished products and the shorter process times, resulting therefrom, compared with conventional thermosetting fiber composite materials.B · US 2017/0157819 A1 · ¶ 4
Therefore, it is an object of the present invention to provide a method, a device and a component which avoids, or at least reduces, the disadvantages of the prior art.B · US 2017/0157819 A1 · ¶ 8
patent.fyi, US 2026/0356429 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356429/, SHA-256 ea3aeab73752831bac144ce7c3e2fc254d3b62d6a6b5eb96c2341966ddc44383