1.1Open frame with cargo clamps
Rubber-lined jaws grip the lower frame tubes of a portable generator at four points. Rollers carry the sliding frame and clamped generator toward the tailgate for unloading.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Rubber-lined jaws grip the lower frame tubes of a portable generator at four points. Rollers carry the sliding frame and clamped generator toward the tailgate for unloading.
Two equal-length arms swing in horizontal planes about vertical pins mounted beside the deck. The arms and crossbar form a parallelogram linkage that carries the bar through an arc, and spring-loaded pins engage holes in sector plates to hold selected positions.
A transverse channel at the front edge of the deck carries a captured carriage that supports the front end of a fore-aft load bar. A roller supports the rear end on the deck, and a hand lever locks the carriage against the channel wall.
Captured carriages carry swivel eyes along the longitudinal tracks and lock into detent holes with spring-loaded pins. Ratchet straps connect opposite eyes and tension over the cargo to hold it against the deck.
Reinforced socket pairs at fixed fore-aft stations receive downward-facing pins at the ends of the bar. The operator withdraws the retaining clips, lifts the bar clear of both sockets, and lowers it into another pair.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A greenhouse transport cart carries a fixed deck with a longitudinal track along each side. Two movable standoffs support a transverse load bar above the deck, and rubber-lined saddles bolted to the bar hold the upper ends of upright plant stakes. The operator moves the bar to align the saddles with the stake bases in a deck tray and inserts spring-loaded pins into holes in both tracks.
Two continuously supported round steel shafts replace the longitudinal tracks and run along opposite sides of the deck. Each standoff bolts to a carriage with two open recirculating ball bushings, with the bushing openings facing the shaft support. A transverse load bar joins the standoffs, and a hand lever on each carriage clamps a split collar onto its shaft to hold the bar in position.
A rectangular steel tube replaces the load bar track and bolts to end plates on the two movable standoffs. Paired holes through the tube walls accept transverse bolts that secure cargo stop brackets, and steel sleeves between the walls carry the bolt clamping force. The operator sets the fore-and-aft position by moving the standoffs along the deck tracks and sets the lateral spacing by bolting the brackets into the selected holes.
A 1,200 mm long deck carries two longitudinal tracks spaced 800 mm apart on center. The standoffs hold one transverse load bar with its underside 300 mm above the deck. Each track has 17 indexing holes on 50 mm centers, giving 800 mm of adjustment, and captive 8 mm pins engage matching holes on both sides.
A hand-cranked cargo winch mounts to the front crossmember of the sliding deck frame, and its line runs along the deck centerline. A roller fairlead bolts to the middle of the raised transverse load bar, with the line running through the fairlead to a wheeled equipment cradle. Captive pins secure both standoffs to the longitudinal tracks before cranking, and the fairlead sets the height of the line where it approaches the cradle.
A lead screw runs beside each longitudinal track, and a captive nut connects each screw to its standoff. One geared motor turns both screws through a toothed belt, while the tracks guide the standoffs and carry the raised bar. A controller homes the assembly against a reference switch and uses an encoder on a screw to move the bar to stored positions. End switches stop travel at either limit, and a spring-applied motor brake holds the position when power is removed.
An 18 mm phenolic-faced plywood panel bolts to steel crossmembers with countersunk fasteners. Epoxy coats the cut edges and drilled holes to limit moisture uptake.
Interlocking aluminum extrusions form the load surface, and integral underside ribs stiffen the spans between crossmembers. Raised serrations on the upper faces provide traction for cargo.
A roll-formed steel channel runs fore and aft along the deck edge with its inward-facing lips flush with the load surface. A removable end stop permits insertion of a carriage and retains it during use.
A rectangular aluminum crossbar bolts to two standoffs with polymer shoes captured in parallel longitudinal tracks. Spring-loaded pins engage holes spaced 50 mm apart, and a pull handle retracts both pins to release the bar for repositioning.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The vehicle body portion 102 includes a cargo deck 104 capable of receiving cargo (not shown).B · US 2009/0284036 A1 · ¶ 23
The guide rail is disposed on the cargo deck 104, and more specifically, on the cargo deck floor 110. The sliding cargo floor 114 is adapted to slide on the guide rail and is capable of assuming a retracted position and a plurality of extended positions on the cargo deck 104.B · US 2009/0284036 A1 · ¶ 26
A sliding crossmember 26 is mounted so as to slide on the ring 35.A · US 2007/0033950 A1 · ¶ 20
An empty cell means only that no passage was reproduced there.
However, an antirotation device of this type is difficult to manufacture.A · US 2007/0033950 A1 · ¶ 6
In addition, the cutout reduces the weight of the sliding crossmember.A · US 2007/0033950 A1 · ¶ 9
Accordingly, there exists a need for providing additional cargo space in vehicles for accommodating various cargo sizes.B · US 2009/0284036 A1 · ¶ 5
Another object of the present invention is to provide an occupant of the vehicle with options for configuring the additional cargo space to accommodate various cargo sizes.B · US 2009/0284036 A1 · ¶ 8
patent.fyi, US 2026/0356440 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356440/, SHA-256 137b0a8046753468fee609c007009642aa194ba86cc58a2a6a7e33069c044394