1.2Exposed rider saddle
A padded saddle bolts to a tubular frame above the battery enclosure. Frame-mounted footrests carry the rider’s feet, and a handlebar provides steering and braking controls.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A padded saddle bolts to a tubular frame above the battery enclosure. Frame-mounted footrests carry the rider’s feet, and a handlebar provides steering and braking controls.
A replaceable molded tail panel extends aft of the bumper and closes the tapered upper body. The recessed bumper beam attaches to the rear frame rails through crush boxes.
The wing terminates at two uprights anchored to the rear frame rails. A bearing at each tip transfers aerodynamic loads into its upright and allows the wing to rotate about a transverse axis.
A flat undertray feeds a shallow throat ahead of the rear axle, where accelerated flow lowers static pressure beneath the body. An upward-sloping diffuser aft of the throat expands the passage and recovers pressure toward the outlet.
Bolted pedestals with machined mounting faces set the wing incidence and transfer bending loads into a rear crossmember. The wing generates downward force as air flows over and under it during forward travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A closed-course racing kart carries a transverse wing on a cantilever bracket bolted to the rear frame crossmember above the chain guard. A screw actuator under the seat slides the wing along the bracket through a pushrod. The wing projects behind the rear bumper on track and retracts fully ahead of the bumper for transport on a storage rack.
A telescoping rectangular box beam replaces the fixed support bracket and mounts to a structural crossmember beneath the rear deck. The inner tube carries the wing on a central saddle, and replaceable polymer wear pads between the tubes transmit bending loads and prevent rotation. A lead screw inside the beam moves the inner tube between stops that place the wing behind the bumper when extended and entirely ahead of it when retracted.
A 1,600 mm wide wing with a 240 mm projected chord mounts on a longitudinal carriage with 300 mm of travel. The forward stop places the trailing edge 300 mm ahead of the vertical plane through the rearmost bumper point, and the intermediate stop places the trailing edge flush with that plane. The aft stop places the trailing edge 60 mm behind the bumper plane when the carriage has 360 mm of total travel.
A reversing camera mounts high on the rear body above the wing, and the wing controller receives the reverse gear signal from the transmission controller. Selecting reverse commands the actuator to move the wing entirely ahead of the bumper. The controller holds the wing forward while reverse is selected, and the camera displays the area behind the bumper throughout the movement.
An actuated diffuser pivots beneath the rear floor, and a separate actuator translates the cantilevered wing above the rear bumper. A shared controller uses a calibration table indexed by vehicle speed and rear ride height to select diffuser angle and wing position. At low speed, it sets the diffuser flush with the underfloor and retracts the wing ahead of the bumper, while calibrated higher-speed settings extend the wing behind the bumper and adjust the diffuser angle to suit the measured ground clearance.
A controller reads vehicle speed and steering angle from the vehicle network and reads wing position from an actuator encoder. Above 90 km/h, it commands an intermediate wing position during straight travel and full extension when absolute steering angle exceeds 8 degrees for 200 milliseconds. Below 70 km/h, it retracts the wing entirely ahead of the bumper, and separate steering thresholds for extension and return stabilize the command near the transition.
Two extruded aluminum sill rails run parallel to the vehicle centerline between front and rear bulkheads. Bonded and riveted crossmembers connect the rails and support the floor panels.
Stamped high-strength steel pillars join the roof rails and door sills around the passenger compartment. Spot-welded floor crossmembers provide mounting points for the seat tracks.
A molded bumper fascia forms the rearmost surface of the body. An expanded polypropylene absorber sits behind the fascia and transfers compression loads into a transverse steel beam.
An electric motor turns a lead screw that drives a traveling nut attached to the wing carriage. Twin longitudinal rails guide the carriage between end stops that place the wing’s trailing edge aft of the bumper when extended and forward of it when retracted.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As illustrated in FIG. 1, the front body of the automobile 1 includes, in a plan view, a pair of left and right front side frames 2 extending in the vehicle front-rear direction with a predetermined distance away from each other in the vehicle width direction; a crash can 3 connected to a front end of each of the front side frames 2 and extending in the vehicle front-rear direction; a bumper reinforcement 4 for connecting front ends of the crash cans 3 in the vehicle width diB · US 2018/0244317 A1 · ¶ 26
An engine room S and a passenger compartment (not illustrated) are isolated from each other by the cowl panel 10 and the dashboard panel 11.B · US 2018/0244317 A1 · ¶ 28
Provided that the rear bumper 1 is secured to the rear end of the vehicle by a bolt or the like, the rear bumper 1 will be completely fastened to the vehicle body. The rear bumper 1 is restricted in all directions with respect to the rear side outer panel 3, and thus, the rear part of the vehicle body is formed according to the original design.A · US 6,962,380 B2 · ¶ 26
An empty cell means only that no passage was reproduced there.
Thus, some rear bumpers should have assembly structures for fixing the rear bumper to the rear side part of the vehicle.A · US 6,962,380 B2 · ¶ 3
Embodiments of the present invention provide a rear bumper assembly structure for a vehicle that is fixed at the rear side part of the vehicle without the need for additional components, thereby reducing a vehicle's weight, facilitating the assembly process, and improving the maintenance process.A · US 6,962,380 B2 · ¶ 4
Thus, there is a problem that it is difficult to secure an installation space for auxiliary machines on the vehicle rear side on an upper portion of a cowl panel.B · US 2018/0244317 A1 · ¶ 6
Thus, there is a problem that welding workability may be lowered.B · US 2018/0244317 A1 · ¶ 8
patent.fyi, US 2026/0356443 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356443/, SHA-256 29dcb8292f38af8975bf082ee4f538637ca2fa2bf3af0cf97356a11f82fcd461