1.1Flexible webbing support
Two webbing loops pass beneath the weight and carry its vertical load in tension. A transverse strap draws the weight against a rubber pad on the vehicle frame and limits swinging.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two webbing loops pass beneath the weight and carry its vertical load in tension. A transverse strap draws the weight against a rubber pad on the vehicle frame and limits swinging.
A cast frame crossmember contains an upward-facing pocket sized to receive the lower edge of the weight. The pocket floor carries the vertical load, its walls limit horizontal movement, and a hinged lid restrains upward movement.
A bent steel rod forms the bracket, with one rod leg alongside each end of the handle. Two split clamps each capture a rod leg and the adjacent handle segment in separate grooves, transferring load through contact with the groove walls.
Two ears on the base extend over the ends of the handle opening. A single cross pin slides through both ears and the opening beneath the handle grip, where a spring detent retains it.
A formed steel saddle on the base follows the handle profile and provides a broad bonding surface. A two-part structural epoxy cures between the prepared metal surfaces and transfers load across the saddle in shear.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A flat bracket bolts to the lower frame of a mobile stage scenery cart, and a base plate bolts to the bracket. The base plate rests against the flat upper face of a suitcase weight. Two straight bolts pass through the handle opening and draw a backing bar against the underside of the handle, securing the weight to the cart.
Two adjustable over-center draw latches take the place of threaded clamp bolts and mount on the base at opposite ends of the handle opening. Each latch has a hook that passes through the opening and catches the underside of the handle. Closing the levers draws the handle into a saddle on the base, and spring catches hold the levers shut.
Two captive quarter-turn cam pins replace threaded bolts in a base fixed to the bracket. The pins pass through the handle opening and engage matching cam receptacles in a backing bar hinged to the base. A 90-degree turn of each pin draws the bar upward against the underside of the handle, and spring detents hold the pins in the closed position.
An 8 mm steel base plate bolts to the bracket and carries three pairs of 9 mm holes on 40, 60, and 80 mm centers. Two M8 bolts pass through the selected hole pair and the clear handle opening into a tapped backing bar. The installer selects the widest pair that clears the handle ends and tightens both bolts to draw the backing bar against the underside of the handle.
A bracket bolts to the lower crossmember of a three-point hitch carrier, and its base plate bears on the flat top of a suitcase weight. Two straight bolts pass through the handle opening into a tapped backing bar below the handle. Raising the hitch lifts the carrier and weight together, while a lower ledge on the carrier supports the weight from below.
Two straight bolts pass through the base and the handle opening into a tapped backing bar, and a load-sensing washer sits beneath each bolt head. A controller records the two washer readings after tightening and samples them during operation. It displays a service indicator when either reading stays below 80 percent of its recorded value for 10 seconds.
A bent low-carbon steel plate forms a vertical mounting face and a horizontal support leg. Two triangular gussets welded between the faces stiffen the bend against downward loading.
A formed steel base has a shallow saddle that follows the upper surface of the weight handle. Fillet welds along both sides join the base to the bracket foot and transfer load into the bracket.
Two flange-head bolts pass through the base and thread into a steel clamp bar beneath the handle. Tightening the bolts draws the bar toward the base and grips the handle between the two surfaces.
Two steel pins slide through separate pairs of holes in the base and cross the handle opening below the grip. Spring-loaded locking balls retain each pin after it passes through the far wall of the base.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Mounting bracket. 22. c shaped flange 30.A · US 9,394,919 B1 · ¶ 30
The shroud (canopy) 40 with mounting bracket 20 is attached to a ceiling junction box 30 which is usually attached to joists 12 behind a ceiling 15.A · US 9,394,919 B1 · ¶ 61
The method can include disposing the bracket base on a tooth and coupling the bracket body with the bracket base via the first bracket footing.B · US 2019/0321137 A1 · ¶ 7
An empty cell means only that no passage was reproduced there.
This installation has generally involved supporting the heaviest part of the fan by hand or by a hanger until the wiring is completed before the fan can be installed, which can be physically dangerous to the installer since the work involves the installer standing on a ladder with their hands holding heavy weights above their head.A · US 9,394,919 B1 · ¶ 3
A secondary objective of the present invention is to provide devices, apparatus, systems and methods of hanging ceiling fans, which allows for the wiring connections to easily, occur while the ceiling fan mounting bracket is installed.A · US 9,394,919 B1 · ¶ 8
Since teeth are different, several sizes and configurations of orthodontic brackets are made which can create manufacturing difficulties.B · US 2019/0321137 A1 · ¶ 4
The bracket base can be separately conformable to a tooth while the bracket can be mass produced.B · US 2019/0321137 A1 · ¶ 5
patent.fyi, US 2026/0356444 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356444/, SHA-256 8215113d686b115142880de49ac8d32025569d92b727294a244b87c9d4247db5