1.1Stamped plate support
Two bolts secure the wide base of the plate to the moving input bracket, and the holder mounts at the narrow upper corner. Bent edge flanges stiffen the plate as it transfers hand force to the bracket.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two bolts secure the wide base of the plate to the moving input bracket, and the holder mounts at the narrow upper corner. Bent edge flanges stiffen the plate as it transfers hand force to the bracket.
A two-piece clamp secures the holder to the middle of the rod. A key between the clamp and the rod transfers torque from the grip into the rod during operation.
A contoured pad transfers palm pressure to a pivoting input arm. A torsion spring on the pivot returns the arm to its starting position when the operator lifts the hand.
An eccentric-mass motor bolts to an external face of the holder beneath a protective cover. The rotating mass shakes the holder, and the grip attachment transmits the motion to the hand.
A flat rubber pad bonds to both mounting faces across its full area. The pad carries hand loads in compression and shear, and it flexes as the grip vibrates.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rod fixed to the moving table of a manual milling machine carries a holder with a bored recess. A keyed stem on the grip fits into the recess, with molded elastomer pads between the stem flats and the opposing recess walls. A linear vibration actuator inside the grip receives a pulse command from a table position controller when encoder readings reach a preset travel limit. The keyed stem transmits the operator’s push or pull to the table, and the pads reduce vibration transmission into the rod.
A piezoelectric bending actuator with a tip mass serves as the vibration source inside a hollow grip. A clamp secures one end of the actuator to a rib on the grip shell and leaves the weighted end free to oscillate. A driver applies alternating voltage near the actuator’s mounted resonance, and the reaction at the clamp vibrates the grip shell. The grip stem engages a recess in the rod-end holder through elastomer pads that transmit hand loads and attenuate vibration.
Four preloaded stainless steel leaf springs replace elastomer pads between the flat faces of the grip stem and the walls of the holder recess. Each spring has one end clamped to the holder and a rounded free end that bears on a stem flat. A transverse retaining pin passes through an oversized hole in the stem, permitting small radial deflections while retaining the stem axially. An actuator inside the grip moves the stem against the springs, which flex and return the stem toward the center of the recess.
A 16 mm square grip stem enters a 20 mm square recess in the rod-end holder, with 20 mm of overlap. Each of the four stem faces carries a polyurethane pad measuring 8 mm wide by 15 mm long and 2.2 mm thick before assembly. The 2 mm clearance at each face precompresses the pads by 0.2 mm, and a transverse pin through an oversized stem hole retains the grip axially while allowing small lateral motion. An internal vibration actuator drives the grip laterally, alternately compressing and unloading the opposing pads.
A hand-operated steering tiller carries a holder with a recessed socket, and elastomer pads support the grip stem within the socket. An ultrasonic parking controller reads rear bumper transducers while reverse is selected and sends its minimum measured distance to a grip controller over a wired link. The grip controller drives a vibration motor inside the grip at one pulse per second from 0.6 to 1.2 m and three pulses per second below 0.6 m. A flexible wire loop at the stem accommodates motion between the grip and the holder.
A rod-end holder receives the grip stem, with elastomer pads between the stem and the walls of the recess. A linear actuator and an accelerometer mount to the inner wall of the grip, with the accelerometer sensing along the actuator’s drive axis. A microcontroller filters the acceleration signal around the drive frequency and calculates its root mean square over successive groups of vibration cycles. A proportional-integral controller adjusts the actuator drive voltage within preset limits to maintain the commanded acceleration as hand pressure changes.
A round steel tube has a 22 mm outside diameter and a 2 mm wall thickness. A welded flange at its base bolts to the moving input bracket and transfers bending loads and torque.
A linear electromagnetic actuator mounts to an internal grip rib with two screws. An alternating coil current drives a spring-supported mass along the grip axis at 175 Hz.
A glass-filled nylon grip has an integral cylindrical spigot that projects 18 mm from its mounting face. A chamfer on the leading edge guides the spigot into the holder bore during assembly.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A hollow housing houses the socket at the distal end such that access to the socket is provided and such that the electrical wire extends from the socket, through the housing, through the hole in the mounting spigot and through the hollow mounting device such that electrical power may be supplied to the socket.A · US 7,329,023 B2 · ¶ 14
An electrically powered low-power illumination apparatus for mounting to a building surface, comprising: a hollow mounting device securely placed within a hole formed in the building surface such that the mounting device is contained within the hole, wherein the internal surface of the hollow mounting device is threaded; a mounting spigot having a hole through which an electrical wire may extend and adapted to be removably secured to the mounting device, wherein the externalA · US 7,329,023 B2 · claim 1
In addition, the bearing bushing assembly 100 comprises an elastic bushing in the form of a rubber bushing 20, which encloses the bearing bushing 10 on the outside and establishes contact on the outside with the outer tube 120 of the steering shaft.B · US 2013/0118291 A1 · ¶ 16
An empty cell means only that no passage was reproduced there.
Of the illumination devices invented, there are none that provide a secure apparatus for mounting a low-power illumination apparatus in a window sill or other surface inside a residence or other building.A · US 7,329,023 B2 · ¶ 8
Further, the secure embedded attachment of the low-power illumination apparatus to a wood structure minimizes the chances of the low-power illumination apparatus and its attendant low-voltage wiring from being separated, thus minimizing the chance of electrical shorts from the exposed wiring.A · US 7,329,023 B2 · ¶ 9
While the provided sealing ring or wiper seal reportedly offers reliable sealing against moisture and dirt, the use of such a design in steering systems revealed that the conventional bearing bushing assemblies contribute to a significant extent to the transmission of acoustic and mechanical vibrations between the chassis and the driver's cab.B · US 2013/0118291 A1 · ¶ 2
Because the bearing bushing is enclosed by an elastic bushing, and more particularly by a rubber bushing, damping that acts notably in the radial direction is achieved between the bearing bushing and the exterior steering shaft tube (outer tube), whereby the noise development and/or transmission are considerably reduced.B · US 2013/0118291 A1 · ¶ 6
patent.fyi, US 2026/0356454 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356454/, SHA-256 4ae9a1be81d79ab8ff221fc80c8b4eff2e208c5d7037a86a7979230848e594b9