1.1Sidewall mounting above the deck
Triangular brackets carry the platform from reinforced vertical frames behind the cockpit sidewall. Through-bolts and backing plates transfer the seat load into the frames.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Triangular brackets carry the platform from reinforced vertical frames behind the cockpit sidewall. Through-bolts and backing plates transfer the seat load into the frames.
Two tubular hangers descend from transverse cabin beams and carry the seat pivot at their lower ends. The hangers transfer occupant weight into the overhead structure, and locking pins hold the seat in either orientation.
The platform carries a fixed, level seat pan with a guide rail along each side. The backrest travels on roller carriages and locks with spring pins at the aft end for forward-facing use or at the forward end for aft-facing use.
A flat, symmetrical pan rides on straight fore-and-aft rails and locks at either end of its travel with a transverse pin. The pan slides toward the bow for forward-facing use against a fixed aft backrest and toward the stern for aft-facing use against a fixed forward backrest.
A vertical swivel bearing carries the seat pan and its attached backrest through 180 degrees. A pull pin locks the bearing at each position, and the same upper cushion face supports the occupant in both positions.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A floor-mounted frame supports a two-surface seat between control consoles at opposite ends of a rail inspection cab. A transverse shaft carries the seat in bearings on the two sides of the frame. The operator withdraws a spring-loaded pin and rotates the seat until the selected seating surface lies parallel to the cab floor. The pin engages a hole in an indexing plate at each operating position.
Bonded rubber torsion bushings replace the shaft bearings at the ends of the transverse seat axis. Each outer sleeve is clamped to the platform, and each inner sleeve is keyed to a seat trunnion. The bushings are installed with the seat held midway through its travel so the rubber twists in opposite directions at the two seating positions. Stop blocks carry seating loads at both positions, and a pull pin holds the seat against the selected stops.
Two arcuate guide tracks on the platform replace the transverse pivot shaft and its bearings. Each side of the seat carries a pair of captured rollers that follow a track centered on the transverse seat axis. The rollers guide the seat between end stops that set the two deck-parallel seating positions. A hand-operated latch engages a keeper at each end of travel.
A common platform carries two 450 mm wide seat modules on 520 mm centers. Each module has its own transverse trunnions and rotates through 90 degrees between stops that set the selected seating surface parallel to the deck. Separate pull pins engage indexing plates at the ends of travel so either module can be repositioned independently.
A deck-mounted platform houses a marine stowage drawer below the seat pivot, with the drawer opening toward the aisle. Fixed side uprights carry the pivot bearings and support the seat at both travel stops. The drawer runs on full-extension slides below the lowest point of the seat's swept path. A push-button latch retains the drawer when closed, and the drawer opens in either seating position.
A geared electric motor drives the transverse seat shaft through a toothed belt, and load cells between the pivot frame and deck platform detect occupancy. A controller releases a spring-engaged locking pin and starts rotation when the operator holds the direction switch and the measured load stays below the empty-seat threshold. A limit switch stops the motor when the selected surface reaches its deck-parallel position, and the pin engages a hole in the indexing plate. A pin-position switch confirms engagement before the controller indicates that the seat is ready for use.
A bent aluminum plate forms the platform and has two base flanges seated on the deck. Stainless steel through-bolts clamp the flanges to backing plates beneath the deck.
Two uprights rise from opposite sides of the platform and carry the seat above the deck on stub shafts. Stops on the uprights set the two operating positions, and a spring-loaded latch engages a slot at each stop.
A stainless steel shaft runs athwartships through a seat frame and turns in polymer sleeve bearings. The seat frame makes a half-turn about the shaft to change its facing direction.
Two closed-cell foam cushions attach to opposite faces of a rigid seat core. Adjustable stops set the rotation endpoints so the exposed seating surface lies parallel to the local deck plane in each facing position.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The invention may also be used on boats having, for example, a separate platform attached to the transom 114 or even with boats that do not have a reboarding platform 150.B · US 2020/0130786 A1 · ¶ 27
Each aft-facing seat 202, 204 is moveable to allow access to the compartment 250 from the swim platform 160.A · US 10,336,411 B2 · ¶ 36
The moveable seat bottom 614 operates similarly to the forward member 214 of the sun pad seat 210, discussed above, and is moveable between a reclined position (shown in FIG. 12) and an inclined position (shown in FIG. 13).B · US 2020/0130786 A1 · ¶ 47
In this embodiment, the seat bottom 210 and seatback 220 pivot together because they are integrally formed, but in other embodiments, they can be moved separately, or only one of the seat bottom 210 and the seatback 220 may be moveable.A · US 10,336,411 B2 · ¶ 36
Each of the main seat bottom 612 and the moveable seat bottom 614 also includes an upper surface 622, 624. In the reclined position, the upper surface 622 of the main seat bottom 612 and the upper surface 624 of the moveable seat bottom 614 are at substantially the same height, forming a substantially flat surface and a continuous bench seat.B · US 2020/0130786 A1 · ¶ 47
An empty cell means only that no passage was reproduced there.
In the first position, the upper surface of the forward member forms a substantially flat surface with the upper surface of the aft member, and, in the second position, the upper surface of the forward member is inclined upward relative to the upper surface of the aft member such that it forms a seatback for the first aft-facing seat.B · US 2020/0130786 A1 · ¶ 6
patent.fyi, US 2026/0356460 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356460/, SHA-256 b82c48aff6e034f1ed3d8012561342a3ed7a3c7c6895c2b2859e25d959f7bb79