1.1One platform per loading cycle
A roller bed carries one platform to a retractable stop at the exit. The stop retracts and a motorized roller feeds the platform down a launch ramp. A deck hoist loads the next platform after the roller bed clears.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A roller bed carries one platform to a retractable stop at the exit. The stop retracts and a motorized roller feeds the platform down a launch ramp. A deck hoist loads the next platform after the roller bed clears.
Two parallel roller lanes support the platforms at the same height. Each lane has a retractable stop and a powered feed roller that releases its platform independently through a shared end opening.
Four posts bolt directly to the vessel deck and carry retractable support fingers at each storage level. Lower guide rails carry the bottom platform over the stern while the upper fingers retain the remaining platforms. A lifting tray takes the weight of the next platform, lowers it to the rails, and returns beneath the stack.
Guide rails bolt to the outer face of a solid structural beam and engage shoes on the sides of the platforms. A screw-driven carriage indexes the stack downward by one platform pitch while individual latches retain the platforms. At the lower end, a transfer arm releases the lowest platform onto a stern chute.
A movable tray aligns the lowest platform with the side hatch. A transverse ram pushes the platform onto an outboard roller chute while retaining fingers support the rest of the stack.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A reservoir survey boat carries a vertical container holding three stacked instrument floats with recessed temperature and conductivity probes. A hand-cranked lead screw lowers a cradle under the bottom float, while opposed latches engage molded shoulders on the float above it. At the lower exit opening, a fixed cam tips the cradle and the float slides down a short chute into the water.
A tubular aluminum frame and a tensioned polyester fabric sleeve replace a rigid-walled container body. The frame bolts to the vessel and supports two longitudinal guide bars that carry a stack of floating sensor platforms, while the sleeve encloses the space around the stack. A hand lever retracts a transverse retaining bar at the low end of the inclined frame, and the stack slides through the exit opening along the guide bars.
A stack of nesting glass-fiber cradles replaces direct hull-to-hull stacking inside a vessel-mounted container. Each cradle has padded saddles for one monitoring boat and four corner posts that transmit stacking loads between cradles. At the lower exit opening, a mechanical escapement releases the lowest loaded cradle into a fixed tipping frame, which tilts the boat into the water and retains the empty cradle.
A 1.5 m tall container on a sheltered-water service vessel holds four workboats, each 600 mm long, 350 mm wide and 180 mm high, with their support rims spaced at a vertical pitch of 250 mm. Fixed guides keep the stack aligned over a 650 mm by 400 mm bottom opening. A two-stage escapement engages the rim of the next workboat before releasing the bottom workboat, and a screw-driven follower lowers the remaining stack by one pitch after each release.
A vessel carries a vertical container above an existing moon pool, with its lower exit opening aligned with a guided submersible cradle. The cradle rises to receive the lowest survey float while support pins hold the remaining stack inside the container. The moon pool winch lowers the cradle until the float lifts free under buoyancy and moves out through the open side of the cradle.
A vessel-mounted container holds stacked water-quality floats above a chute with a motorized escapement at the exit opening. A controller reads a tilt sensor on the container and a photoelectric sensor across the chute, then releases one float when roll and pitch stay within 5 degrees for 3 seconds and the chute is clear. The controller records the release once the chute sensor detects the float passing and the escapement position switch confirms that the gate has closed.
Four molded feet on each platform seat in recessed pads on the platform below. The feet transfer the stack load through the frames and leave clearance between adjacent hull surfaces.
Two removable polymer crossbars between adjacent platforms maintain a fixed vertical pitch. Grooves in the crossbars seat against frame rails and locate each platform laterally.
A welded marine-grade aluminum body rests in two deck cradles lined with elastomer pads. Captive steel pins pass through cradle lugs and mounting ears on the body to resist uplift and longitudinal motion.
A door hinged along the lower edge of the exit opening swings down to form an extension of the compartment floor. Two rows of rollers guide each platform out of the compartment, and mechanical stops set the deployed ramp angle.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Alternatively, the support system may comprise a framework system generally forming a plurality of berths or bays in a stacked configuration. Further, a plurality of support columns and cross beams may be used to form a series of berths, wherein the size of the berths is adjustable for accommodating different size craft.A · US 2011/0052350 A1 · ¶ 4
The glove box 22A includes an interior space or compartment 26A that can be accessed through an opening 30A of a bin structure 34A when door 24A is in an open position.B · US 2015/0360616 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
Though somewhat effective, there are various deficiencies associated with such facilities, including the need for implementing a more efficient dry watercraft storage system which can handle and store a large number of watercraft configurations and sizes.A · US 2011/0052350 A1 · ¶ 2
The storage system is adaptable and adjustable to different sized/shaped craft or other items, and may provide systems for maintaining the craft systems operational.A · US 2011/0052350 A1 · ¶ 1
After the door has been opened, the actuator automatically closes the door after a predefined period of time has passed from the opening of the door.B · US 2015/0360616 A1 · ¶ 3
The actuator may comprise a mechanical device such as a spring that biases the door towards the closed position, or the actuator may comprise an electric motor or other suitable powered actuator.B · US 2015/0360616 A1 · ¶ 3
patent.fyi, US 2026/0356462 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356462/, SHA-256 6c6671eeff05e8928a7f1ff9a2afcc10d9c2d6073b449aa09fbcefa75dcfe038