1.1Direct regulator outlet
The bite piece seals around the regulator outlet. Inhalation deflects a diaphragm that opens the gas inlet valve, and exhaled gas exits through a separate exhaust port.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The bite piece seals around the regulator outlet. Inhalation deflects a diaphragm that opens the gas inlet valve, and exhaled gas exits through a separate exhaust port.
A straight rigid spigot aligns the bore of the bite piece with the inlet leg of the breathing tube. The tube bends beyond the spigot to direct its open end above the water surface during surface swimming.
A light compression spring presses the poppet against an annular elastomer seat. When pressure inside the mouthpiece exceeds external water pressure by the opening threshold, the poppet lifts and water flows around it through radial outlet slots.
A retaining frame clamps the plate and a flat gasket against a molded land around the drain opening. Water passes through the opening to the valve body mounted on the exterior face of the plate.
The ribs extend from the valve support and bear against molded pads on the inner wall to resist rocking. The open space between the ribs carries breathing gas and lets water reach the drain inlet.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stationary rowing trainer supports an ambient-air tube on an adjustable arm beside the seat. A flexible hose connects the tube to a curved bite mouthpiece with a drain sleeve sealed through the underside of the bend. A rigid web follows the bend and joins the sleeve to a transverse tubular portion aligned with the breathing passage. A membrane seated in the sleeve opens outward during a clearing breath and closes during inhalation.
A molded silicone duckbill valve replaces the membrane shutter and its separate valve body. A retaining ring clamps the duckbill flange against an annular shoulder in the drain sleeve, with the slit facing outward. A rigid curved web connects the sleeve to the transverse air passage inside the mouthpiece bend. Positive pressure in the mouthpiece spreads the lips to discharge water, and reverse pressure presses the lips together.
The curved connector has two drain bores centered 30 degrees to either side of the bottom of its circular cross-section. A common rigid web connects two sealed sleeves to an 18 mm circular air passage, and each sleeve carries an outward-opening membrane over a 5 mm outlet. With the connector rolled 30 degrees to either side, one drain bore occupies the low point of the bend. A clearing breath drives pooled water through the lower outlet, and inhalation seats both membranes.
A guided float and an annular inlet seat mount at the upper end of the breathing tube. The tube connects to a curved bite mouthpiece with a transverse tubular insert linked by a curved web to a sealed membrane drain sleeve at the bottom of the bend. Rising water lifts the float against the inlet seat, and the float drops when the inlet returns above the surface. A clearing breath expels residual water through the membrane at the bend.
A captured swivel joint connects the breathing tube to the inlet of the curved bite mouthpiece. Two radial elastomer seals surround the open bore, and a retaining collar captures a shoulder on the rotating tube end. Inside the bend, a rigid web joins the transverse tubular passage to the sealed drain sleeve, which holds an outward-opening membrane. The tube rotates about the inlet axis while the drain stays oriented with the mouthpiece, and a clearing breath discharges water through the membrane.
An infrared emitter and photodiode sit outside a sealed transparent prism molded into the bottom of the mouthpiece bend beside the drain sleeve. The rigid insert connects the sealed sleeve to a transverse tubular air passage through a web along the inner bend. An air interface reflects the emitted light toward the photodiode, while water against the prism reduces the received signal. A controller samples the signal at 20 Hz and pulses a vibration motor after ten consecutive readings below a calibrated wet threshold.
A molded polymer tube has an elliptical bore and a smooth inner wall. The lower end transitions gradually to a round socket that mates with the mouthpiece connector.
A single molded silicone part forms two inward bite tabs and a smooth curved passage. An annular bead at the tube end engages a matching groove on the breathing tube.
A central pin holds a thin silicone disc against an annular seat on the valve body. Pressure from inside the mouthpiece lifts the disc perimeter for drainage, and external water pressure presses the perimeter onto the seat.
A rigid polymer sleeve fits into a through hole in the mouthpiece curve and supports the valve body on an internal shoulder. An elastomer ring in a circumferential groove seals radially against the hole wall, and an outer flange sets the insertion depth.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In all embodiments, the snorkel includes a snorkel tube and the diving regulator includes a breathing chamber.B · US 2015/0020799 A1 · ¶ 25
The diving regulator includes a diaphragm/purge valve chamber in fluid communication with the breathing chamber and a diving regulator mouthpiece in fluid communication with the breathing chamber.B · US 2015/0020799 A1 · ¶ 25
An air vent plug 10 may be inserted through the wall 12 of the milk tube portion 14 of the teat liner 16.A · US 2013/0125822 A1 · ¶ 14
An empty cell means only that no passage was reproduced there.
The upper mouthpiece further comprises a mouthpiece transition, a mouthpiece lip, and a groove on an outer surface of the upper mouthpiece to provide flexibility in the upper mouthpiece.A · US 2013/0125822 A1 · ¶ 3
A liner series with increasing flexibility in the mouthpiece, decreasing axial thickness of the mouthpiece lip, and/or decrease transverse thickness of the mouthpiece transition from L1 through Ln allows a dairyman to choose the right balance and trade-off between milking speed/harvest and liner slippage for his particular needs.A · US 2013/0125822 A1 · ¶ 5
This invention relates, generally, to an integrated snorkel and diving regulator for use while snorkeling near a water surface and while diving under water.B · US 2015/0020799 A1 · ¶ 2
Thus there is a need for an integrated diving snorkel/regulator that combines the operation of a snorkel with that of a diving regulator, enabling snorkeling and underwater diving using a single apparatus.B · US 2015/0020799 A1 · ¶ 6
patent.fyi, US 2026/0356464 A1, claim 1, first published 2026-11-20T01:43:50-05:00, https://patent.fyi/US20260356464/, SHA-256 5e7c89e162a7f0387d75ad74ef62704e0dc19c4fe9e441669e5f762b5819f88f