1.1Fixed outlets with flow apportionment
A motor-driven cylindrical valve meters fan discharge into an aft-facing duct and a downward-facing duct. The ratio of jet momentum at the two outlets sets the direction of the combined thrust.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A motor-driven cylindrical valve meters fan discharge into an aft-facing duct and a downward-facing duct. The ratio of jet momentum at the two outlets sets the direction of the combined thrust.
Two pods attach to fuselage frames through short pylons, and each pod houses a row of electrically driven ducted fans. Each fan draws air through a forward inlet and discharges through a short aft duct.
A rigid aluminum panel forms the duct floor below the fans. An electric actuator moves a tie rod that rotates vanes mounted on shafts between the nozzle sidewalls, changing the discharge angle.
A flexible duct at the hinge feeds fan discharge into a plenum inside the flap. A full-span slot at the flap trailing edge accelerates the flow, and flap rotation changes the slot's discharge angle.
A curved transfer duct routes fan discharge through the lower element to a slot nozzle flush with its underside. The slot directs the jet tangentially along the underside, where a curved flap surface turns it downward.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A conveyor dryer uses a transverse row of ducted fans in an overhead air delivery module. Each fan discharges through an outlet upstream of a hinged flap, and air travels over the upper face of a fixed lower panel before crossing onto the flap. A geared actuator rotates the flap between a shallow angle for spreading heated air along the belt and a steeper downward angle for directing it onto the product.
A spring steel flexure panel replaces the rigid hinged flap in the lower element of a wing containing ducted fans. The panel clamps to a fixed shelf downstream of the exhaust outlets, with its upper surface flush with the shelf at the joint. An electric screw actuator beneath the panel moves its aft edge through a spanwise load distribution bar. Downward travel increases panel curvature and turns the exhaust downward.
A wing section contains six ducted fans with 180 mm rotor diameters on 220 mm spanwise centers. The lower lip of each outlet feeds a fixed shelf that extends 40 mm aft to the leading edge of a shared flap with a 120 mm chord. Two synchronized actuators set the flap at either 0 or 20 degrees downward relative to the shelf. At the 20 degree setting, the flap turns the discharge downward as it passes over the flap upper surface.
A wing with ducted electric fans combines lower flap actuation with the electronic speed controllers that drive the fan motors. Each outlet discharges rearward across a fixed shelf into the leading edge of a downstream flap. A supervisory controller uses measured flap angle and a calibration table to adjust motor speed commands as the flap moves. The speed controllers use rotor speed feedback to track the adjusted commands and compensate for changes in airflow caused by flap motion.
A wing with distributed ducted fans uses independently actuated lower flap segments on the left and right sides. Each segment begins aft of its associated outlets, and a fixed shelf guides the discharged air onto the segment upper surface. A flight control mixer adds a roll rate correction to one flap command and subtracts it from the other. The resulting difference in exhaust direction changes the vertical force on the two sides and produces a rolling moment.
A five hole pressure probe sits on an aft support in the exhaust stream behind a movable lower flap. The fan outlets lie forward of the flap leading edge, and the exhaust reaches the flap across the upper surface of a fixed shelf. A controller converts pressure differences into a discharge angle using probe calibration data. It compares the measured angle with a commanded angle and drives the flap actuator within configured travel and rate limits.
An aluminum flap pivots on three bearing blocks along a spanwise hinge. An electric motor drives a ball screw connected to a flap horn, moving the flap between a flush position and a position 25 degrees below the wing chord line.
Four ducted electric fans sit side by side between wing ribs. A carbon fiber sandwich panel below the fan housings forms the fixed portion of the lower element and carries the flap hinges at its aft edge.
Adjacent fan ducts merge into a rectangular outlet bounded by upper and lower lips and two sidewalls. The outlet plane sits 40 millimeters forward of the flap leading edge in both flap positions.
A position controller drives a rotary actuator on the lower flap hinge and uses a shaft encoder to stop at the commanded angle. Rotating the flap downward brings its curved upper surface into the path of the jet that crosses the lower element, turning the jet downward.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Yaw motion is generally controlled by the deflection of a rudder, or a hinged section at the rear of the aircraft 802.B · US 2020/0079515 A1 · ¶ 79
In some embodiments, the aircraft has a first wing and a second wing and the first and second sub-assemblies are mounted to the first and second wings.B · US 2020/0079515 A1 · ¶ 29
Specific examples of AFC device and AVG locations on embodiment wings may include: 1) the AFC device being located upstream of the AVG on a main element of the wing, and the AVG being located along a hinged line (e.g., just downstream) between a trailing-edge flap and the main element of the wing; 2) the AFC device being located downstream of the AVG on the main element of the wing, and the AVG being located along a hinged line (e.g., just downstream) between a drooped leadinA · US 2016/0280358 A1 · ¶ 36
Systems, methods, and devices are provided that provide hybrid flow control for a simple hinged flap high-lift system using sweeping jet (SWJ) actuators for active flow control (AFC) and adaptive vortex generators (AVGs) that may be actuated by flap deflection for passive flow control (PFC).A · US 2016/0280358 A1 · abstract
An empty cell means only that no passage was reproduced there.
Therefore, what is needed for transport aircraft, is a flow control method that enables a simple hinged flap system to achieve higher flap deflections without flow separation, and thereby achieve lift enhancement comparable to a complex conventional systems (e.g., Fowler-flap systems).A · US 2016/0280358 A1 · ¶ 5
The various embodiment hybrid flow control systems, methods, and devices may significantly reduce mass flow, differential pressure, and power requirements for equivalent flow control performance when compared to using AFC only.A · US 2016/0280358 A1 · ¶ 6
Therefore, there is a need for improvement to existing architectures.B · US 2020/0079515 A1 · ¶ 4
Features of the systems, devices, and methods described herein may be used in various combinations, in accordance with the embodiments described herein.B · US 2020/0079515 A1 · ¶ 8
patent.fyi, US 2026/0356472 A1, claim 1, first published 2026-11-20T02:22:52-05:00, https://patent.fyi/US20260356472/, SHA-256 a8ccdb602b391cd395eec93ad497a6fe8c206ca44b18a002359ec9410fd9f30c