1.1Single housing with integral contacts
Spring contacts in the stationary housing press against pads that form part of the vehicle skin. A return spring retracts the housing along a guide after a latch releases, opening the circuits.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Spring contacts in the stationary housing press against pads that form part of the vehicle skin. A return spring retracts the housing along a guide after a latch releases, opening the circuits.
A lug on the mating section enters a clevis and aligns its bore with the clevis bores. A pin passes through all three bores and carries separation load in double shear. An actuator withdraws the pin to clear the lug.
The receiver bore pilots the mating section while spring-loaded jaws close around a flange outside the bore. A yoke retracts the jaws radially until their tips clear the flange.
A chamfer on the mating stem expands the ring during insertion, and the ring contracts behind a shoulder when the stem seats. A wedge driven between the ends of the ring expands it far enough for the shoulder to pass during withdrawal.
The plug advances axially and pushes the segment tips outward into an annular groove in the receiver. When the plug retracts, a spring draws the tips inward and clears the groove.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A fixed coolant manifold carries the receiver and its spring-biased outer collet segments, while a removable machine skid carries the inner collet segments and sliding sleeve. Two self-closing coolant couplings sit on either side of the collet axis and mate as guide pins align the skid with the manifold. Skid insertion drives the sleeve into its engagement position, and a pneumatic actuator advances the sleeve for secondary engagement or retracts it for primary release. A hand lever retracts the sleeve for secondary release, and the coolant couplings close as the skid withdraws.
A rotary collar with three helical cam slots replaces the axially sliding outer sleeve. Follower pins pass through the slots and connect to an axially guided support ring that moves beneath the inner collet segments to hold them against the receiver segments. During insertion, an axial plunger acts through a rack and pinion to turn the collar toward engagement, and a hand lever turns it back for secondary release. A double-acting pneumatic rotary actuator turns the same collar toward secondary engagement or primary release.
Individual torsion springs replace a shared circumferential spring for biasing the receiver segments inward. Each spring fits over a segment pivot pin and bears against the receiver body and a pocket in the segment, while a receiver shoulder carries the axial load from the locked segment. During insertion, chamfers rotate the outer segments outward until their locking faces align with the inner segments, and the springs then return the outer segments inward as the sleeve supports the inner segments. Pneumatic retraction or manual lever retraction withdraws the sleeve, allowing the inner segments to collapse inward as the sections separate.
A receiver with a 100 mm guide bore carries eight outer collet segments on 45-degree centers, and the mating section carries eight aligned inner segments. A longitudinal key aligns the segments before their locking faces meet, and the sleeve has a 10 mm axial stroke between its support land and release relief. The insertion shoulder advances the sleeve mechanically, and a manual linkage retracts it for secondary release. A double-acting pneumatic actuator drives the same stroke for secondary engagement and primary release.
A robot wrist carries the sleeved inner collet assembly, and each interchangeable tool carries a receiver with spring-biased outer segments. Tapered guide pins register the two plates, and floating electrical and pneumatic connectors mate as the wrist seats against the tool plate. Wrist insertion advances the sleeve for mechanical engagement, and the wrist air circuit drives the sleeve for secondary engagement and primary release. A tool rack supports the tool during release, and a lever on the wrist plate provides secondary mechanical release.
An inductive sensor in the receiver detects full insertion, and two limit switches indicate the engaged and retracted sleeve positions. A controller energizes the pneumatic engagement valve only when the insertion sensor and the engaged-position switch confirm mechanical engagement. On a release command, the controller drives the pneumatic actuator in the retract direction and enables the withdrawal drive only after the retracted-position switch closes. A manual lever also moves the sleeve to the retracted position and actuates the same switch during secondary release.
A flanged aluminum body forms the fixed section, and a cylindrical stainless steel plug body forms the removable section. A locating key aligns the electrical contact inserts as the plug enters the fixed body.
Four outer collet segments slide radially in slots inside the receiver. A circumferential spring band bears on their outer surfaces and presses their tips inward into a groove on the mating section.
Insertion force against a receiver cam moves the outer sleeve axially until a cylindrical sleeve land holds the inner collet tips in engagement. A hand lever pulls the sleeve back for secondary release and aligns an internal recess with the tips so they can move radially clear.
An annular piston attached to the outer sleeve divides a cylinder into two sealed air chambers. Air pressure in one chamber moves the sleeve to hold the inner collet segments engaged for secondary locking. Pressure in the opposite chamber aligns a sleeve relief with the segments to permit primary release.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The connecting element has two coupling halves (1a, 1b) that can be interconnected by jointing and can be fixed to components or subassemblies to be connected by fixing means.A · US 7,175,207 B2 · abstract
When attaching the cover 100 to the mobile electronic device 110, the larger diameter section 162 of the male part 158 is passed through the smaller diameter section 174 of the female part 170, and the male part 158 and/or the female part 170 are radially, elastically deformed to allow passage.B · US 2013/0223005 A1 · ¶ 19
An empty cell means only that no passage was reproduced there.
It is accordingly problematic that, in prefabricated building construction, manufacture of the building components can be carried out with a high degree of automation and a high production quality can also be achieved, whereas, during installation of the prefabricated elements on site, the speed of installation and the quality of work can, in contrast, be influenced only to a small extent.A · US 7,175,207 B2 · ¶ 4
The invention relates likewise to a device for effectively connecting sub-assemblies in a very great variety of forms to wall, ceiling and floor surfaces of buildings or frameworks.A · US 7,175,207 B2 · ¶ 6
Insecure or loose fitting covers interfere with the usability of the device, as do bulky covers.B · US 2013/0223005 A1 · ¶ 1
FIG. 5 is a perspective view of the cover of FIG. 1 with the cover shown open and propped in a screen typing position for viewing and typing on the mobile electronic device.B · US 2013/0223005 A1 · ¶ 6
patent.fyi, US 2026/0356507 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356507/, SHA-256 eaf188f7f49827568c0863a450eae1a048c4f340d394339ca6e05761e6edc390