1.1Independent wing rib mounts
A short bracket at each motor station bolts to a reinforced wing rib. Each rib transfers motor thrust and reaction torque to the wing spars.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A short bracket at each motor station bolts to a reinforced wing rib. Each rib transfers motor thrust and reaction torque to the wing spars.
Two box sections meet at a reinforced joint and sweep in opposite spanwise directions from the joint. The motor mounts hold the thrust axes vertical while the box sections carry the loads to two wing attachment points.
Split saddles clamp around a closed rectangular tube at the motor stations. Each motor bolts to a plate on its saddle, and the flat faces of the tube resist saddle rotation under motor torque.
A constant-section box beam carries bending through its upper and lower skins. Internal frames around the motor openings transfer mount loads into the skins and side webs.
Two reinforced fuselage frames carry sockets that receive the roots of the lift arms. Retention pins secure the arms, and the spacing between the sockets reacts the bending loads from lift thrust.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An orchard mapping aircraft carries a downward-facing multispectral camera beneath its fuselage and a suspended lift arm beneath each fixed wing. Each straight arm contains multiple motor openings and tapers from the opening regions toward both ends. The arms provide vertical lift for departures and landings in row-end clearings, and a separate cruise propeller drives the aircraft along survey passes.
Two-piece aluminum collars replace the motor openings in each straight, tapered arm body. The upper collar halves bolt to reinforced pads on the underside of the arm, and the lower halves capture flanges on the stationary motor housings. The flanges transfer axial thrust to the collars, and a locating pin at each flange transfers motor reaction torque.
Pneumatic vane motors replace electric lift motors in the openings of each straight, tapered arm on a tethered test aircraft. A ground compressor feeds a regulated air line that runs through the tether to a distribution manifold on the aircraft. An electrically actuated proportional valve meters air to each motor, and a shaft speed sensor supplies feedback for individual propeller speed control. Quick-disconnect air and electrical fittings at the wing interface permit removal of each arm.
Each wing carries a 2.4 m straight suspended arm with four motor openings on 600 mm centers. The openings are centered 300, 900, 1500, and 2100 mm from the forward end, and the arm narrows from the motor support regions toward both tips. Each motor drives a 460 mm propeller, which leaves a nominal 140 mm gap between adjacent rotor disks on the same arm. Adjacent motors turn in opposite directions to balance reaction torque at equal thrust.
A pumped liquid cooling system connects the lift motor housings and their electronic speed controllers to a radiator in the fuselage. Each motor sits in a separate opening in the straight, tapered arm, and a cooling jacket surrounds its stationary housing. Parallel branches from supply and return manifolds feed the motor jackets and controller cold plates. Shutoff couplings at the wing attachment let the arm detach while retaining coolant on both sides of the connection.
A memory device in each detachable arm stores the position, rotation direction, and thrust calibration of every motor mounted in the arm openings. At power-up, the flight controller reads the memories through the wing connectors and uses the loaded center of gravity to calculate each motor's roll and pitch moment arms. A constrained least-squares allocator converts requested lift and body moments into motor thrust commands within the stored thrust limits. The controller checks whether the installed motors can produce the takeoff thrust and control moments before enabling vertical takeoff.
Two molded carbon fiber shells bond along overlapping flanges to form the outer arm body. Spanwise fibers in the upper and lower skins carry bending, and angled plies in the sidewalls carry shear.
The arm centerline follows one straight line when viewed from above. In side view, the arm drops below the wing at the root and runs level along the motor stations.
Two circular openings in the arm each receive a lift motor housing. A flanged aluminum ring at each opening centers the housing and carries the motor mounting bolts.
Two wing clevis fittings receive matching lugs on the arm, and cross bolts retain the lugs in double shear. The arm installs for a higher takeoff weight configuration, and a keyed electrical connector links its motor controllers to the aircraft.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
FIG. 1 shows an example of a three-boom excavator, wherein a first boom 1 and a second boom 2 are the supporting booms, whereas a third one 3 serves as an excavating boom which is connected to a bucket 4.A · US 2006/0090974 A1 · ¶ 14
The outer tubing element 20 is depicted as segments 20A and 20B, which are divided by a support segment 25 of the movable pane 16 extending collinearly from the straight boom 22.B · US 8,496,425 B2 · ¶ 22
The indexable master boom 12 includes a straight boom 22 and an offset boom 24.B · US 8,496,425 B2 · ¶ 22
An empty cell means only that no passage was reproduced there.
The cylinder is strongly stressed because during particularly heavy-duty excavation operations—for example when working on hard ground—the pressure of the fluid inside of it may be very high, as it is proportional to the reaction force that the cylinder needs to exert to keep the two booms in a relative fixed position.A · US 2006/0090974 A1 · ¶ 3
Therefore, the purpose of the present invention is to solve the above-mentioned problems and to propose a device and method for braking the supporting booms of an earthmoving machine, for example an excavator, and a machine equipped with said device, capable of reducing the reaction force of the positioning cylinders.A · US 2006/0090974 A1 · ¶ 4
Applications of robotic apparatuses with end-effectors can encompass material handling, manufacturing, packaging, and testing.B · US 8,496,425 B2 · ¶ 3
With limited die opening and three dimensional die shapes, a flat end-effector frame with a straight boom may interfere with the dies and machine frames during movement of the workpiece.B · US 8,496,425 B2 · ¶ 5
patent.fyi, US 2026/0356511 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356511/, SHA-256 73ce109348cd6c7b3f3c119c8a26df35f7279b7efd473227131b17c380ca9c14