1.1Overhead support for the stack
The crossbeam suspends two vertical guide rails with free lower ends. Retractable pawls on each platform engage seats on the rails at the stacking heights and transfer the platform weight to the crossbeam.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The crossbeam suspends two vertical guide rails with free lower ends. Retractable pawls on each platform engage seats on the rails at the stacking heights and transfer the platform weight to the crossbeam.
A collar fixed to the platform carries rollers that run on the four faces of the mast. Two vertically spaced rows of rollers resist platform tilt as the collar travels.
Roller carriages carry each platform along two horizontal rails to a transfer station above the stack. A lifting cradle takes the platform weight, releases the carriage latches, and lowers the platform until it rests on the stack.
Two sleeve housings bolt to the underside of the crossmember between the deck edges. Each housing carries a linear bushing that slides on a vertical rail passing through a clearance hole in the deck.
A conductive fin under the platform passes between opposed permanent magnets near the bottom of travel. Eddy currents in the fin dissipate descent energy as heat, and the seating pads carry the platform after touchdown.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A stainless steel base carries two vertical guide rails at a food processing wash station. Empty perforated trays slide down the rails on opposing side supports, and raised pads on each tray provide landing surfaces for the next tray. Two elastomer boots surround the rails at each landing level, with an axial opening at each end of each boot. The boots compress as the trays land and leave a gap between trays for drainage.
Two hydraulic dashpots replace the impact absorbing boots at the base. Each dashpot mounts beside a guide rail with its piston rod vertical and directly below a contact pad on the corresponding platform support. As the platform descends, the pads depress the piston rods and force fluid through metering orifices to dissipate impact energy. Return springs extend the rods after the platform is lifted, and fixed stops carry the platform at rest.
The base carries two vertical guide rails that are 300 mm tall, 16 mm in diameter, and spaced 240 mm center to center. A 4 kg loaded carrier slides on opposing side supports and contacts two base-mounted elastomer boots during the final 8 mm of travel. Each boot has an 18 mm axial opening at each end, and the pair absorbs at least 0.40 J over the available stroke at a contact speed of 0.20 m/s. Fixed stops limit boot compression to 8 mm and carry the seated load.
Two annular elastomer boots sit side by side around each guide rail, with the shorter boot nested concentrically inside the taller one. Each boot has an axial opening at both ends, and the inner diameter of the taller boot leaves radial clearance around the shorter boot for compression. A flat pad on each platform support contacts the taller boot first and reaches the shorter boot after 3 mm of descent. Both boots compress together over the next 5 mm before a rigid stop arrests travel.
A powered roller conveyor feeds platforms into a stacking station where a vertical lift carriage grips each platform at its front and rear edges. The carriage raises the opposing slide supports above the two rails, and a horizontal shuttle on the carriage positions the supports over the rail tips. The carriage lowers the platform along the rails until paired annular boots cushion contact with the base or the platform below. The grippers release after the carriage transfers the platform weight to the stack.
A motorized lifting carriage lowers the platform along two vertical guide rails through opposing side supports. A downward-facing distance sensor on each support measures the gap to the landing surface, and the controller slows descent to 20 mm/s when either gap reaches 15 mm. An annular elastomer boot cushions contact at each rail, and a force sensor beneath each boot measures the transferred load. The controller stops the drive when both force readings reach their seating thresholds and raises the platform if the difference between the measured gaps exceeds 2 mm during the final approach.
Rectangular steel tubing forms a welded frame with crossmembers beneath the rail mounting plates. The crossmembers carry landing loads into the frame and distribute them to four leveling feet.
Two ground, hardened steel shafts stand vertically in split clamps bolted to the base. A removable upper crossbar holds the shafts at a fixed center spacing.
A flanged housing bolts to each of two opposing sides of the platform. Each housing contains two axially spaced recirculating ball bushings that slide on the corresponding round rail and resist housing tilt.
Each molded polyurethane boot has an upper axial opening and a lower axial opening joined by a clearance passage for the guide rail. Lateral cavities collapse under axial compression, and the area under the measured loading force–displacement curve up to the permitted stroke sets the impact energy capacity.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Meanwhile, the conventional washing machine 1 may further include a bedplate (pedestal) 20 for supporting the main body 10 on a floor. In this case, the main body 10 is installed on the bedplate 20.A · US 2010/0101282 A1 · ¶ 13
In contrast thereto, the rotary bearing points of the short scissor arm 17 of the Y-scissors 14 and of the link 15 provided on the bearing leg 8 of the fixed-frame-side support bracket 5 are provided on a slider 18, which is movably guided along the bearing leg 8 in the longitudinal direction thereof. In this instance, the slider 18 engages, by means of longitudinal edges extending in the movement direction, behind associated longitudinal edges of the bearing leg 8 having a C-shaped cross-section.B · US 10,550,618 B2 · ¶ 41
An empty cell means only that no passage was reproduced there.
The present invention relates to a pedestal washing machine serving as a bedplate of a washing machine or the like, and more particularly to a pedestal washing machine including a water supply device capable of simultaneously or selectively supplying water to a washing machine and the pedestal washing machine from an external water supply source.A · US 2010/0101282 A1 · ¶ 1
Accordingly, a long washing time and a large amount of energy are consumed.A · US 2010/0101282 A1 · ¶ 5
It is an object of the present invention to increase the stability of the mounting of a rotationally and translationally movable sash of a window or a door, on an associated fixed frame with respect to above-cited state of the art, in particular also in the case of varying installation conditions.B · US 10,550,618 B2 · ¶ 10
Due to their attachment to both rebate surfaces of the fixed-frame corner and the sash corner respectively, the two support brackets create a load-bearing connection between the sash and the fixed frame.B · US 10,550,618 B2 · ¶ 12
patent.fyi, US 2026/0356515 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356515/, SHA-256 c3dff677dcb67f02222bb6eac3cae8b0ca9ac7b3600616aef763c539f95f605f