1.1Side by side bays
A vertical divider separates two floor tracks, and each track holds one wheeled inspection platform. The platforms drive through adjacent lanes at the open end of the container.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A vertical divider separates two floor tracks, and each track holds one wheeled inspection platform. The platforms drive through adjacent lanes at the open end of the container.
An elevator lowers the platforms one at a time from the stack to the hatch. The hatch folds down into a ramp, and each platform drives across it.
Each cantilevered shelf holds one wheeled platform in the open air. A carriage travels along the mast, stops flush with a shelf to receive the platform, and lowers it to ground level.
Overhead electromagnets attract steel plates on the platforms, and gap sensors regulate coil current to maintain vertical clearance. Opposed lateral electromagnets center each platform, and the controller lowers it onto an exit track for release.
A perforated plenum beneath each lightweight platform supplies a pressurized air film that carries its weight. Opposed side jets center the platform, and a rear jet moves it toward the opening while the air film stays pressurized.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A vertical loading column in a greenhouse holds a stack of wheeled crop inspection carts above an outlet at its lower end. Each cart rests on structural pads on the cart below it, and a pivoting floor inside the outlet supports the bottom cart by its chassis. A lift fork enters the column beneath the second cart and takes the weight of the upper stack before the floor pivots down to transfer the bottom cart onto a ramp. The floor closes, and the lift fork lowers the remaining stack onto it before withdrawing.
Two endless flat belts replace the stationary support inside a vertical container that opens at the top. The belts run in vertical planes on opposite sides of a stack of folded inspection aircraft, and their inward runs press against flat pads on the aircraft housings. Spring-loaded backing rollers maintain belt pressure, and a braked gearmotor holds the stack in place when the belts stop. A common drive moves both inward runs upward to feed the top aircraft through the opening onto a receiving tray.
A cable and counterweight replace the powered drive for a platen that supports stacked inspection aircraft inside a top-opening container. The cable runs over a sheave at the top of the container and connects the platen to a counterweight in a separate vertical channel beside the compartment. The counterweight exceeds the combined mass of the platen and full stack, and a rotary damper limits the speed of the sheave. After the uppermost aircraft leaves the opening, a foot pedal releases an indexing pawl for one step, and the pawl engages the next notch when the following aircraft reaches the opening.
A top-opening container accepts two to four folded inspection aircraft with a common stacked height of 100 mm and body widths of either 220 mm or 320 mm. Two slotted guide plates set the compartment width to 226 mm or 326 mm, and a 200 mm wide elevator platen supports the bottom aircraft. The elevator runs on a screw drive with 300 mm of travel, and its starting position places the uppermost aircraft at the opening. After that aircraft leaves, the platen rises 100 mm to present the next one.
A vertical container holds stacked inspection aircraft on a platen that rises inside the compartment. A motorized rotary indexing table sits beside the top opening, with a receiving tray at the height of the platen's discharge position. A linear pusher transfers the uppermost aircraft onto the tray, and the table rotates the tray to a position with clearance for the aircraft to unfold and take off. The table returns the empty tray to the transfer position before the platen raises the next aircraft.
A motorized platen supports a stack of folded inspection aircraft inside a top-opening container. A distance sensor above the opening measures the height of the uppermost aircraft, and the controller drives the platen until that aircraft reaches the transfer height. A separate optical beam at the opening detects the aircraft as it leaves the compartment. The controller waits for the beam to clear before driving the platen again and stops the drive if a lower limit switch or motor current limit indicates a feed fault.
Bent aluminum panels form an elongated rectangular compartment with a closed rear bulkhead and an open front end. Two wheeled inspection platforms occupy vertically spaced positions, and their folded profiles clear the front opening.
A panel hinged to the lower edge of the end opening closes the compartment during transport. The panel lowers into a ramp, and an internal lift aligns each platform in the stack with the ramp entrance.
Two aluminum angle ledges project inward from the compartment walls and bear against the underside of a platform chassis. Polymer wear strips on the ledges provide sliding contact as a linear pusher moves the chassis toward the opening.
Two spring-loaded steel pins project into recessed sockets on opposite sides of a platform chassis and carry the chassis in shear. A common cam retracts both pins after a transfer cradle takes the platform's weight.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
A payload launch system, comprising: a launch tube defining a launch chamber with a first end and a second end opposite the first end; a payload disposed within the launch chamber, the payload is ejectable through the first end of the launch chamber; a payload ejection mechanism within the launch tube and engaged with the payload to eject the payload through the first end, the payload ejection mechanism includes an inflatable air bag ram fixed in the launch chamber at the secB · US 10,464,693 B2 · claim 1
This FIG. 3 also shows the interior surface of the barrel 12 including an annular retaining ledge generally shown at 42 configured to retain the needle stem 24 distally thereof such that the needle stem 24 is securely seated in the syringe barrel distal end, including during attachment of needle assembly 18, and until a complete retraction of the needle stem 24 and needle assembly 18 into cavity 30.A · US 2012/0232482 A1 · ¶ 13
An empty cell means only that no passage was reproduced there.
The present invention is directed to safety syringes, and particularly syringes with retractable needles configured to retract after use and prevent re-use and unintended sticking.A · US 2012/0232482 A1 · ¶ 2
There is desired a retractable syringe configured to enable the retaining ring to break from the needle stem with a reduced plunger engagement force, which provides an improved tactile feeling of the syringe plunger and comfort of use.A · US 2012/0232482 A1 · ¶ 3
The launch tube can be used to transport and protect the payload from harsh environments for extended periods prior to launch.B · US 10,464,693 B2 · ¶ 8
The payload can be any unmanned payload that one may wish to transport and launch, and protect the payload from harsh environments for extended periods of time prior to launch.B · US 10,464,693 B2 · ¶ 8
patent.fyi, US 2026/0356520 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356520/, SHA-256 6be5aea655e1a983fee744027f0af83dafb556b14c04c65bcfa4e8d96b5d88c1