1.1Open transport frame
Bolted aluminum crossmembers carry padded saddles that support the platforms during transport. Cam straps hold the platforms against the saddles and release before unloading.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Bolted aluminum crossmembers carry padded saddles that support the platforms during transport. Cam straps hold the platforms against the saddles and release before unloading.
Parallel floor channels position each platform at the same elevation. A spring detent holds each platform in its bay until a release lever retracts the detent for unloading.
A removable cassette supports the platforms during transport. The cassette slides through a side opening onto a foldout table, where its discharge edge aligns with two exterior guide rails.
A captive door panel slides horizontally in upper and lower tracks to expose the side opening. An internal tray runs on telescoping slides and carries the platforms through the opening.
A spring-loaded pin on the floor bracket passes through a transverse hole in the launch element near its base. A pull handle retracts the pin to release the launch element while the top operates independently.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A transport case holds a vertical stack of pipe inspection crawlers on a guide post that passes through a chassis opening in each crawler. A cylindrical recess beneath the sliding top receives the upper end of the post when the top is closed. At the inspection site, an operator slides the top aside and lifts each crawler off the post for insertion into the pipe.
Two pairs of flat-faced cylindrical rollers replace the concave segment at the upper end of the stack guide. The pairs sit at right angles on a bracket beneath the top and bear against four flat faces on the guide tip. As the hinged top closes, the rollers ride over chamfers on the tip and locate it in two lateral directions. Opening the top carries the bracket and rollers clear of the guide.
Two parallel rectangular rails replace a single stack guide and engage open slots on opposite sides of each platform. A rigid crosshead joins the upper ends of the rails and carries a central locating boss that enters a recess beneath the closed top. The crosshead fits within the clear space between the inner edges of the platform slots, so each platform slides past it when lifted off the rails. The rail spacing sets the platform orientation throughout removal.
A transport case holds six indoor inspection platforms with a 25 mm stacking pitch on a 180 mm vertical guide measured from the stack support. A 12 mm diameter guide tip enters a 12.5 mm diameter recess in the top, which provides 8 mm of engagement when closed. A vertically removable top lifts at least 10 mm before moving sideways to clear the tip.
A charging backplane runs along one wall of the compartment parallel to the stack guide. Each tier has a current-limited charging channel and a pair of spring contacts that bear on pads at the edge of the corresponding platform. The closed top seats the guide tip in a recess, and the guide maintains lateral registration between the pads and contacts. A top-position switch disables charging as the top lifts, and the platforms slide upward past the contacts during removal.
An inductive proximity sensor sits behind a thin polymer wall at the base of the recess and detects a steel target in the guide tip. A separate switch reports whether the top latch is engaged. A controller samples both inputs at 20 Hz and records the case as secured after both signals remain active for 0.5 seconds. If the latch engages without a seating signal for 0.5 seconds, the controller illuminates a fault indicator.
Folded aluminum sidewalls join to a welded floor to form the interior compartment. A continuous elastomer gasket along the upper rim compresses against the closed top.
Two parallel guide rails extend into the compartment and pass through guide bushings on each platform. Spacer collars set the gap between adjacent platforms in the stack while allowing them to slide along the rails.
A continuous hinge connects the top to one edge of the container, and two gas springs assist opening. A stop holds the top at 105 degrees from its closed position and clears the exit path above the platforms.
A semicircular cradle attaches to the underside of the top and receives the round end of the launch element as the top closes. A replaceable elastomer liner compresses against the end to limit movement during transport.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Box (100) includes walls defining an interior portion 102, the interior portion typically having a removable foam or other suitable partition member (102A) which will divide the interior into a launcher storage section (102B) and airborne vehicle storage section (102C), the partition member (102A) providing protection for the two elements to be contained within the interior from one another and assisting and providing for snug receipt of the airborne vehicle and launcher withA · US 7,210,654 B1 · ¶ 54
In this alternate preferred embodiment of aircraft vehicle (300) it is seen that launch system (200) is integral with the container and includes folding legs (502), which folding legs are attached to a rotating leg support rod (508) (see FIG. 3E), the support rod being attached to and articulating on, box corner mounted brackets (504) such that the launch rail may have a pair of fold out longitudinal members (512A) and (512B) which longitudinal members are attached to the remA · US 7,210,654 B1 · ¶ 58
Box (100) may have a housing member (104) and a pivoting hinge (110) mounting lid (106) that may be locked in a closed position through the use of a lock (108). The use of a pivoting lid will allow easy access and removal of the launcher and the airborne vehicle from the box.A · US 7,210,654 B1 · ¶ 54
Enclosure 101 is closed off by a nose cap 103 which makes a watertight seal in launch opening 108. Nose cap 103 is configured to uncover launch opening 108 in order to allow UAV 102 to be launched out of its enclosure.B · US 2015/0008280 A1 · ¶ 38
An empty cell means only that no passage was reproduced there.
Those that are light enough are not compact enough, not in their payload or flight system sufficient for the requirements of many reconnaissance missions, especially “over the hill” short range, short duration missions.A · US 7,210,654 B1 · ¶ 5
It is an object of the present inventions to provide a lightweight (typically less than about 10 pounds), backpackable, image transmitting, ground controllable, programmable, self propelled, unmanned, airborne reconnaissance vehicle for short range (typically less than 6 nautical miles) work that will set up quickly and be launchable from almost any terrain.A · US 7,210,654 B1 · ¶ 6
This invention relates to a launch canister for providing a UAV into airspace above a submerged launch platform.B · US 2015/0008280 A1 · ¶ 2
There is therefore a need for improved apparatus for launching UAVs from a submarine.B · US 2015/0008280 A1 · ¶ 7
patent.fyi, US 2026/0356522 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356522/, SHA-256 16d413dacb0e33452ab652f7a2be866f0fdcddcdf76f477bcd87b5b7d7358f82