1.2Bonded long wall panels
A shallow channel along each long edge of the bottom panel receives the lower edge of a precut wall panel. Hot-melt adhesive fills each channel and holds the wall at its assembly angle after cooling.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A shallow channel along each long edge of the bottom panel receives the lower edge of a precut wall panel. Hot-melt adhesive fills each channel and holds the wall at its assembly angle after cooling.
Four corner posts locate in sockets in the base frame and guide the wall edges in vertical slots. The lower wall edges seat in grooves around the bottom panel, and a top frame locks onto the posts to retain the walls.
Matched heated dies draw a conditioned paperboard blank into a shallow cavity and compress it against a continuous shoulder at the opening. The shoulder sets the ledge width and height around the tray.
Each clip bridges a corner joint and has two legs that pass through punched slots, one in each adjacent rim panel. A crimping die folds the legs against the underside to clamp both panels.
A die cuts the panel outline in 0.5 mm polypropylene sheet and forms reduced-thickness scores along the wall and rim fold lines. A forming fixture folds the panels along the scores, and a heated tool bonds the overlapping wall tabs.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A scored paperboard blank forms a rectangular base, four upright walls, and four outward rim panels. A separate plastic film patch bonds to the two adjacent rim ends at each corner and leaves the mouth open. Textile swatches lie flat on a removable divider grid, and operators grip the two longitudinal rims when transferring the tray between cutting and inspection benches.
Four kraft paper patches with acrylic pressure-sensitive adhesive replace the plastic film pieces. After the walls rise and the rim panels fold outward, each patch spans one corner joint and overlaps both adjacent rim ends by at least 8 mm. A rubber roller presses each patch against the supported rim surfaces to establish the bond.
Four stamped aluminum clips replace the plastic film pieces at the joints between outward rim panels. Each clip has a flat top plate that spans the joint and two rounded tabs positioned along the outer perimeter, one over each adjacent rim end. A forming die presses the plate against the rim and bends the tabs around the outer edges and onto the undersides of the two panels.
A 350 g/m² paperboard blank forms a 240 by 160 mm bottom, 20 mm walls, and 18 mm outward rim panels. The die-cut rim ends meet at 45-degree miters with a nominal 1 mm gap after folding. An adhesive-backed plastic film patch measuring 16 by 24 mm is centered over each miter, with its long dimension perpendicular to the joint, and bonds to both rim ends.
An indexing lug conveyor carries the trays on two parallel belts that support the bottom panel, while adjustable side guides run below the rim. Each conveyor lug pushes against the lower portion of a transverse wall, and separate plastic film patches connect the four pairs of adjacent rim ends. At a loading station, the conveyor stops with the tray mouth under a reciprocating depositor, then advances the filled tray to a discharge belt.
An overhead camera images the four corner joints of a formed tray held in a nest that supports the outward rim panels. Image processing locates the cut edges at each joint and computes a patch position that gives the specified overlap on both rim ends. A Cartesian robot uses a vacuum head to pick individual adhesive-backed plastic film patches from a peel station and presses one across each joint.
Each rail has a downward-facing channel that grips the top edge of a transverse wall and a horizontal ledge that supports a lid. End pockets in each rail capture the ends of the longitudinal rim panels.
A steel rule presses the paperboard into a counter-die groove along each transverse edge of the bottom panel. The resulting creases guide the two end walls as a forming mandrel raises them.
A crease runs along the upper edge of each longitudinal wall panel, parallel to the wall-to-bottom crease. A forming bar turns each 12 mm rim panel outward along the upper crease.
The blank has angled end cuts on the adjoining wall panels, sized for a 15-degree outward flare from vertical. As the walls rise, each longitudinal wall end edge meets the adjacent transverse wall end edge along the corner.
Two rectangular polyethylene film patches bridge the two ends of one transverse rim panel. A heated platen bonds each patch to that transverse rim end and to the adjoining first corner portion of a longitudinal rim panel.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
a conical or frustum-shaped hollow foldable portion, comprising one or more foldable members and a connecting member connected with the base from top to bottom in sequence, each foldable member comprising a first foldable segment, a first fold and a second foldable segment from top to bottom in sequence, and a second fold being disposed between the second foldable segment at a bottom end of the foldable portion and the connecting member;A · US 2018/0327984 A1 · ¶ 8
Next, the left sidewall 29 and right sidewall 29 are folded upward, approximately 90 degrees, along creased lines 13 and then the outer sections 22 are bent or folded roughly 180 degree over inner sections 29A of each of the left side wall 29 and the right side wall 29 along the respective side wall creased sections 14 to form two sides of the cuboid and create apertures 38 between the outer sections 22 and the inner sections 29A on both a front side and a back side of the cuB · US 2020/0270051 A1 · ¶ 41
To create a closed cuboid shown in FIG. 2 the left tab 23 and the right tab 23 of the top end wall 27 are folded inward along the creased lines 13, the left tab 24 and the right tab 24 of the bottom end wall 30 are folded inward along the creased lines 13, and then the top end wall 27 and bottom end wall 30 are folded upward along creased lines 13, loosely forming four sides of the cuboid.B · US 2020/0270051 A1 · ¶ 41
Finally, either or both of the top end wall's extension tab 26 and the bottom end wall's extension tab 30B extend over the top side walls and end walls to cover the cuboid.B · US 2020/0270051 A1 · ¶ 41
An empty cell means only that no passage was reproduced there.
The technical problem the present invention attempts to solve is to provide a foldable traffic cone with respect to the defects of larger overall size, inconvenience in storage and carrying for the foregoing existing traffic cone in the prior art.A · US 2018/0327984 A1 · ¶ 5
What is needed, therefore, is a stylish, versatile, functional yet inexpensive to produce packaging format combined with a complementary doll, which may utilize only fully recyclable or recycled material.B · US 2020/0270051 A1 · ¶ 5
The blank is designed and engineered to be assembled as an appealingly designed and printed box and converts simply to a surprisingly decorated armchair without the use of adhesives or any tools, added attachments or structural components.B · US 2020/0270051 A1 · ¶ 6
patent.fyi, US 2026/0356534 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356534/, SHA-256 2414a9fe5b45c4ae2bbcddc9d03f5d15a5c486cbd1cf52c88bd8e2fd151cad4e