1.1Open-sided storage bay
A folded rear panel and two side panels form a U-shaped bay. Two woven straps span the open front and anchor in slots in the side panels to retain the main load. A pocket in one rear corner holds the plate.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A folded rear panel and two side panels form a U-shaped bay. Two woven straps span the open front and anchor in slots in the side panels to retain the main load. A pocket in one rear corner holds the plate.
Two exterior rails grip the edges of a shallow tray and hold it against the outside face of a tube wall. The tray supports the lower edge of the plate, and a tuck flap closes the top opening.
Two molded support blocks clip into slots at the base of the pocket. A rigid floor panel drops onto ledges on the blocks, where downward pins engage locating holes and keep the panel from shifting under the plate.
Two hooks on the upper edge of a rigid divider seat in slots in overhead rails. Guide blocks capture its lower corners, and a separate shelf carries the plate's weight.
The divider projects through the slot, and a transverse pin fitted into the exposed end limits withdrawal. The slot flanks transfer lateral loads from the divider into the side wall, while the pocket floor supports the plate.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A single die-cut paperboard blank forms an upright rectangular tube for a set of tile samples. Near one corner, a panel folds inward from one side wall to form a horizontal ledge, and its free edge folds upward to form an inner wall whose side edge faces the adjacent wall. A tile sample slides edge-first into the pocket between the inner wall and the first side wall, with its bottom edge resting on the ledge.
A single 0.8 mm solid polypropylene sheet replaces the paperboard blank. Heated crease bars form continuous hinge grooves at the tube corners and at the two pocket bends. The pocket floor folds inward from the first wall, and the inner wall folds upward with its side edge facing the adjacent wall. An ultrasonic lap weld closes the tube at a corner away from the pocket.
A single blank forms a tube with an internal footprint of 420 by 250 mm and an erected height of 300 mm. Three separate panels in the 420 mm side wall each form a 90 mm wide horizontal ledge and a 60 mm high inner wall. The ledges project inward by 8, 12, and 16 mm, measured between the erected pocket faces, and support panels 6, 10, and 14 mm thick, respectively. The outermost inner wall has a side edge facing the adjoining short wall across a 2 mm gap.
A single sheet forms a 340 mm tall tube with a side wall at least 320 mm wide. A panel cut within that side wall forms a 14 mm deep horizontal ledge at 25 mm above the tube base and a 240 mm high inner wall, with a 3 mm gap between its side edge and the adjoining wall. A plate 280 mm wide, 300 mm tall, and 10 mm thick slides in from above and rests on the ledge. The plate extends 60 mm above the inner wall so an operator can grip it for removal.
A single-sheet insert forms an upright tube with two outward-facing mounting ears cut from the upper margin of opposite side walls. The ears seat in molded slots beneath the rim of a reusable stackable tote, and the insert rests on the tote floor. An inward ledge and an upturned inner wall form a pocket next to a tube corner, with the inner wall edge facing the adjoining side wall. An operator loads a flat article from above, and the tote rim carries the load from stacked totes.
An overhead camera measures a flat article's width and height against a calibrated background, and a displacement sensor measures its thickness. Software generates a single-sheet blank with a finished ledge width 2 mm greater than the article width and a finished pocket gap 1 mm greater than its thickness. A cutting and creasing table cuts the blank and marks the corner and pocket folds using bend allowances stored for the sheet stock. On erection, the floor folds inward, the inner wall folds upward, and its lateral edge faces the adjoining side wall.
A die cut defines a tongue in the first wall, leaving intact wall material at both horizontal ends of the first score. The tongue folds inward by 90 degrees to make the floor, and its distal section folds upward by 90 degrees along a second score to face the first wall.
An upright divider folds from the distal edge of the pocket floor and faces the first wall across the plate slot. Its vertical edge next to the adjacent second wall faces that wall's inner surface across a 2 mm gap in the erected member.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Eight interior wall portions (10a) through (10h) are arranged to form the four compartments (8a) through (8d). Interior wall portions (10a) through (10h) are integrally formed with bottom portion (4), and are perpendicular to both the bottom portion (4) and the top portion (5).A · US 8,966,811 B2 · ¶ 18
In the embodiment shown, each compartment may be configured to hold a storage module 446 for storing such items as bank slips, forms, and so on. The storage module 446 may comprise, for example, a tray constructed of plastic or other suitable material with compartments for holding items.B · US 9,984,385 B2 · ¶ 69
An empty cell means only that no passage was reproduced there.
The plurality of such devices coupled with the dangerous hooks thereon and the spread dimensions of the umbrella rig make it difficult to handle and store such loaded rigs without entanglement, injury and/or catching of the hooks in the clothing or boat parts.A · US 8,966,811 B2 · ¶ 7
The present invention attempts to overcome the deficiencies in the prior art umbrella rig storage containers, providing a tackle box in which an umbrella rig can be quickly stored, without disassembly.A · US 8,966,811 B2 · ¶ 10
One perceived shortcoming, however, is that such advertisements are static in nature and display only a very limited amount of information.B · US 9,984,385 B2 · ¶ 3
Briefly described, one embodiment, among others, is a system for conveying digital content to patrons in an establishment.B · US 9,984,385 B2 · ¶ 4
patent.fyi, US 2026/0356537 A1, claim 1, first published 2026-11-20T03:03:17-05:00, https://patent.fyi/US20260356537/, SHA-256 549a5f4f9be882e34f6c1d2a77169d3494f00eede7f8f4bad98a1c517619cea6