1.1Thermoformed polymer cup
A heated sheet draws into a cup mould under vacuum. The formed sidewall holds the product, and a flat rim receives a heat-sealed lid.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A heated sheet draws into a cup mould under vacuum. The formed sidewall holds the product, and a flat rim receives a heat-sealed lid.
A continuous compression-moulded cellulose ring sits between two pulp layers at the rim. The ring resists ovalization when a holder clamps the cup.
A tapered mesh sleeve slides over the dried cup and seats against the underside of the rim. The sleeve bears against the sidewall as the wall deflects outward under load.
An open glass filament fabric lies between two wet pulp layers, which join through the fabric openings during pressing. A continuous inner liner separates the glass filaments from the product.
A heated die locally softens crossing filaments and presses them together so they fuse as they cool. The welded crossings retain the mesh geometry while wet pulp presses through its openings.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A moulded pulp body holds a removable perforated seed basket, and a gasketed lid closes the compartment. An open flax mesh impregnated with cured gelatin is embedded in the wall and follows the upper rim. Two ports in the lid carry conditioned air into the space below the basket and out above the seeds. The mesh stiffens the rim as the chamber cycles between humid and dry air.
A die-cut lattice of regenerated cellulose sheet replaces the impregnated fibre mesh. The lattice has 3 mm square apertures on a 5 mm pitch and wraps around the sidewall with a butt joint. Wet pulp is deposited on both faces of the lattice so pulp fibres bridge the apertures during dewatering. Drying fixes the lattice inside the rigid compartment wall, and a press-fit cap closes the opening.
A closed moulded pulp compartment uses a sliding cellulose acetate shutter in place of a peelable closure. A starch-impregnated flax mesh is embedded in the shoulder around the outlet, where a snap-fit frame captures the shutter in two parallel rails. The shutter has an aperture that registers with the outlet at its open stop to discharge dry granules by gravity. At the closed stop, a solid section of the shutter covers the outlet and a detent holds it in position.
A moulded pulp body has a 4 mm sidewall and a snap-on lid. Two starch-impregnated flax meshes with 5 mm openings lie 1 mm beneath the inner and outer wall surfaces, with the outer mesh rotated 45 degrees from the inner mesh. Wet pulp is deposited in successive layers around the meshes, then dewatered and dried. The two meshes carry tensile loads on opposite faces as the wall bends in either direction.
A cylindrical moulded pulp pod with a quarter-turn lid fits inside a reusable pneumatic tube carrier. A starch-impregnated hemp mesh is embedded around the shoulder where the lid lugs engage. Two elastomer rings seated on the carrier wall grip the pod near its base and shoulder to limit movement during transit. At the receiving station, the carrier opens and the pod lifts out as a closed unit.
An overhead camera measures the outer contour and orientation of a dried starch-impregnated mesh insert on a backlit fixture. Software computes the insert offset from the cavity center and commands a robot to place the insert onto the first wet pulp layer. A second image checks that the insert edge sits at least 2 mm inside the rim before a second pulp layer covers it. The body is dewatered and dried, and a snap-on lid closes the compartment.
Two moulded tabs engage the sealed margins of a flat portion pouch and hold it against the carrier. The pouch provides the moisture barrier, and the carrier supports the pouch during handling.
Vacuum draws a suspension of wood fibres onto a perforated cup mould. Heated matched dies dry and densify the preform while shaping the tapered sidewall and flat sealing flange.
A die-cut lidding film carries a peelable heat-seal layer that bonds to a coated annular pulp flange under heat and pressure. A tab projects beyond the flange for manual opening.
Flax yarns pass through an aqueous gelatinized starch bath, and squeeze rollers remove excess solution. The yarns form an open grid that dries on a shaped fixture before pressing between wet pulp layers.
A woven wool grid takes up warm aqueous gelatin, which an enzyme crosslinks before drying. The dried grid seats against a wet pulp preform, and a second pulp layer covers the grid and bonds through its openings.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
FIG. 2a shows the lower receptacle portion 17 of a coffin according to embodiments herein, provided with an inner spacer structure and an inner shell 19. FIG. 2b shows a complete closed coffin according to embodiments herein with the lid 21 in place on the bottom portion of the coffin 20.A · US 10,974,490 B2 · ¶ 65
A container for holding materials comprising: a molded pulp shell comprising a plurality of pulp shells including comprising a top part and a bottom part that are joined together, or are hinged and foldable to form an enclosed body; molded pulp threads integrally formed on the molded pulp shell; a separate structure removably coupled to the thermoformed molded pulp shell body at a neck of the thermoformed molded pulp shell body; a threaded closure configured to mate with theB · US 11,286,104 B2 · claim 25
An empty cell means only that no passage was reproduced there.
Large containers with smooth surfaces and strong, lightweight structure have been very difficult to pulp mold.A · US 10,974,490 B2 · ¶ 6
Upper and lower coffin halves are pulp molded with integral ribs 44, 46 for reinforcement.A · US 10,974,490 B2 · ¶ 7
Thus, a need exists for improved containers for holding materials.B · US 11,286,104 B2 · ¶ 4
As will be realized, the present disclosure is capable of other and different embodiments, and its several details are capable of modifications in various obvious respects, all without departing from the disclosure.B · US 11,286,104 B2 · ¶ 7
patent.fyi, US 2026/0356557 A1, claim 1, first published 2026-11-20T03:38:56-05:00, https://patent.fyi/US20260356557/, SHA-256 b7d408897abc93b19549d4a1580a9273bc27f1d3a55b21f6ac86be0b7d811e2c