1.1Base captured beneath rim
The holder base forms a split polypropylene collar with inward-facing lugs. The collar expands as the lugs pass over the rim, then contracts so the lugs engage beneath it and resist upward movement.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The holder base forms a split polypropylene collar with inward-facing lugs. The collar expands as the lugs pass over the rim, then contracts so the lugs engage beneath it and resist upward movement.
A polyester strap passes through two slots in the base and wraps around the container wall. A cam buckle locks the strap under tension, and the strap bears against the slot walls when the user opens the holder.
Molded knuckles on the base and peelable portion interleave around a stainless steel pin. Pulling the free edge lifts the seal progressively as the knuckles rotate around the pin.
A silicone gasket sits in a groove on the closed side, inboard of its outer edge and around the applicator recess. A snap latch compresses the gasket against a flat land on the base, and molded gaps vent the outer edge.
Two resilient fingers on the base cradle snap around a groove in the applicator handle. A recessed well in the cradle receives the working tip, and an upward pull releases the handle for use.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A polypropylene holder has a curved adhesive-backed base that conforms to the outside wall of a ceramic glaze jar. A living hinge joins the base to a peelable cover whose closed side carries a flat silicone spatula in two molded clips. The cover's sealing edge presses against the jar wall, and lifting the cover exposes the spatula for spreading glaze on a test tile or scraping residue from the jar.
A pinned hinge replaces the living hinge between an adhesive-backed base and a rigid cover. Interleaved knuckles on the base and cover receive a stainless steel pin, and molded clips on the cover's closed side retain a flat applicator. A flexible bead around the cover's sealing edge presses into a groove in the base frame and releases as the cover lifts.
Two molded silicone suction cups replace the adhesive layer on the container-facing surface of a polypropylene base. The cup stems snap into holes in the base, and pressing the base against a smooth container wall expels air from beneath the cups. A living-hinged cover carries an applicator in a recessed pocket on its closed side and seals against a compressible gasket on the base.
A single 140 mm by 70 mm adhesive-backed base carries two 60 mm by 50 mm peelable covers side by side on the lid of a dispensing pail. Each cover connects to the base through its own 0.4 mm thick polypropylene living hinge and holds a 45 mm long flat applicator on its closed side. Each sealing edge presses against a separate raised rim on the base, so either cover opens independently.
An adhesive-backed holder mounts on the shoulder of a bottle fitted with a hand-operated metering pump. Its living-hinged cover opens against a molded stop that positions the applicator's working surface directly below the pump outlet. The operator dispenses a dose onto the applicator, lifts it from the retaining clips, and returns it before closing the cover against its sealing rim.
An adhesive-backed base contains a battery-powered controller and two magnetic sensors, one aligned with a magnet in the living-hinged cover and one aligned with a magnet embedded in the applicator. A molded pocket on the cover's closed side locates the applicator beside its sensor when the sealing edge seats against the base rim. After the cover closes, the controller samples both sensors and flashes an indicator if the applicator is absent.
A 0.8 mm foam pad with acrylic pressure-sensitive adhesive on both faces joins the holder base to the container wall. The foam compresses under installation pressure and conforms to shallow curvature.
The base and peelable portion form one molded polypropylene part connected by a 0.30 mm web. Radiused transitions join the web to the thicker sections, and the web bends as the peelable portion opens.
A continuous thermoplastic elastomer bead runs along the sealing edge of the closed side. Two snap tabs draw the bead against a matching base land, and molded stops limit bead compression to 20 percent of its free height.
A polypropylene handle carries a flexible silicone paddle that picks up and spreads viscous product. Two molded clips on the closed side grip the handle and hold the paddle above a shallow recess.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The perimeter edge 46 has a rear side 48. The rear side 48 is hingedly coupled to the back side 23 of the plate 18.A · US 2018/0098681 A1 · ¶ 20
The underside of the sealing foot forms an obtuse angle relative to the underside of the lower collar. The sealing foot flexes about a living hinge while remaining outboard from the lower collar and maintains continuous sliding contact with the support panel in response to applied pressure between the seal and the support panel during use.B · US 2020/0300280 A1 · ¶ 11
An empty cell means only that no passage was reproduced there.
The disclosure and prior art relates to spatula cleaning assemblies and more particularly pertains to a new spatula cleaning assembly for cleaning a spatula.A · US 2018/0098681 A1 · ¶ 5
The scraper frictionally engages a spatula such that the scraper removes debris from the spatula.A · US 2018/0098681 A1 · ¶ 6
Push-in type W-base retainers are used in a variety of connection assemblies to secure components of the assembly.B · US 2020/0300280 A1 · ¶ 3
Installing the seal as a separate part is cumbersome and awkward, complicating installation of the retainer.B · US 2020/0300280 A1 · ¶ 8
patent.fyi, US 2026/0356566 A1, claim 1, first published 2026-11-20T03:38:56-05:00, https://patent.fyi/US20260356566/, SHA-256 68f0ff5a8241270833ecf712931e537a6266129cf66b651ca622926d8d888ea2