1.1Threaded cap retention
An internal thread on the cap engages an external thread on the cup. Tightening the cap compresses a flat gasket against an annular sealing face on the cup.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
An internal thread on the cap engages an external thread on the cup. Tightening the cap compresses a flat gasket against an annular sealing face on the cup.
The solid foot supports the pouch connector. A flexible tube runs from a side outlet on the pouch connector to a hose barb on the valve inlet.
A fill nozzle opens a spring-loaded check valve in the pouch wall and pumps product into the pouch. A second check valve in the connector duct opens toward the dispensing valve and blocks inward flow through the duct.
A tapered spigot on the dome foot enters a flexible neck formed from the pouch film. A reusable split collar draws the film against an annular gasket seated on the spigot.
A continuous bead of product-resistant structural adhesive bonds the pouch connector flange to the dome foot around the aligned flow openings. A separate check-valved fill port admits product while the bonded joint stays assembled.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A flexible pouch holds a water-based mold release agent, and its neck is welded to the foot of a detachable connector. The connector mates with the dome end fitting and seals the pouch duct to the passage feeding the crimped spray valve. Regulated air in the chamber surrounding the pouch compresses it, and a hand lever opens the valve to spray the mold surface.
A stainless steel U-shaped spring clip replaces the rotary retention features at the connector interface. The pouch connector slides axially into a socket in the dome end fitting, where a radial O-ring seals the joint around the product passage. The clip passes through two slots in the socket wall and engages an annular groove on the pouch connector. With the dispenser depressurized, withdrawing the clip frees the pouch connector for axial removal.
A threaded compression collar and a molded elastomer ferrule replace the weld between the pouch neck and the connector foot. The pouch has a molded neck with a rigid flange, and the collar captures that flange against the ferrule on the underside of the connector foot. Tightening the collar compresses the ferrule around the product opening while keeping the pouch neck bore aligned with the connector duct. The assembled pouch and connector attach removably to the dome end fitting for dispensing.
A bench dispenser uses a 750 mL pouch with a 10 mm inside-diameter connector duct that mates with a 10 mm passage in the dome. A full-opening valve on the crimped cap feeds a 3 mm outlet, and the combined length of the two 10 mm passages is limited to 40 mm. Air regulated to 150 kPa gauge surrounds the pouch and drives the viscous liquid through the open valve.
A stationary dispenser supplies a low-viscosity coating to a spray gun mounted on a moving gantry. The pouch connector mates with the dome end fitting, and a flexible product hose joins the outlet of the crimped dome valve to the gun inlet. A fixture holds the dome valve open during production, regulated air around the pouch drives liquid through the hose, and the gantry controller triggers the gun valve at the programmed positions.
A load cell supports the complete dispenser, and a solenoid mounted on the dispenser frame depresses the crimped valve stem. A controller opens the valve for a timed pulse, closes it, and waits for the load cell reading to settle. The controller subtracts the settled mass from the pre-pulse mass, uses the result to set the next pulse duration, and stops when the cumulative mass loss reaches the dose target within the configured tolerance.
A formed metal cap carries a spring-loaded stem valve at its center. A crimping head curls the cup rim over the cap flange and compresses an annular elastomer gasket between the flange and the cup.
A molded polymer dome has a 3 mm axial bore through its foot. The bore opens into a counterbore that receives the valve inlet spigot, and a radial sealing ring seals the joint.
A straight 4 mm bore runs along the centerline of the pouch connector. A fill nozzle seals against the bore entrance during filling, and the inlet of the dispensing valve seals against the same entrance during dispensing.
Two radial lugs on the pouch connector enter L-shaped slots in the dome foot and turn through a quarter turn to compress a face seal. A circumferential heat weld joins the polyethylene inner layer of the pouch neck to the polyethylene foot of the pouch connector.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In a third aspect there is provided a spouted pouch for use with a re-usable, rigid container, and comprising a flexible pouch body containing a cleaning liquid which dispenses from a rigid pouch spout and characterized in the provision of an engagement member for engagement with a respective engagement member of the rigid container by which the pouch spout is in fluid communication with the pour spout to allow dispensing of the cleaning liquid stored in the flexible pouch boB · US 2018/0022531 A1 · ¶ 8
The first axial portion 10 has a first end 14 that is an end for connection to a complementary element, for example a tripod joint (not shown). For this purpose, the connection end 14 is provided with connection fluting 16 which in this example is a spline.A · US 2008/0044223 A1 · ¶ 21
The recess 31 is C-shaped (in plan view with the container 3 resting upright on a level surface) and comprises an annular gap which is dimensioned slightly smaller than the diameter of the pouch spout collar to allow the collar 40 to be pushed (by sliding transformation movement) into the recess 31.B · US 2018/0022531 A1 · ¶ 56
An empty cell means only that no passage was reproduced there.
Because of those various fabrication parameters, the structural stability and the service lifetime of the known shaft are compromised.A · US 2008/0044223 A1 · ¶ 5
An object of the invention is thus to increase the structural stability and the service lifetime of a welded tube shaft, while still enabling manufacture to be inexpensive.A · US 2008/0044223 A1 · ¶ 6
This can be difficult to achieve controlled pouring from an unwieldy pouch due to the fluidity of the body.B · US 2018/0022531 A1 · ¶ 9
However when this pack is used within the system of the invention it is possible to achieve controlled pouring from the pour spout into a selected, small location such as a measuring cup or ‘shuttle’ or machine drawer or directly to a fabric stain prior to hand scrubbing/pre-treatment.B · US 2018/0022531 A1 · ¶ 9
patent.fyi, US 2026/0356572 A1, claim 1, first published 2026-11-20T03:38:56-05:00, https://patent.fyi/US20260356572/, SHA-256 11815d9d11417a613c64f417fb70fd3ca76b4ad85656739ec760cb361754899c