1.1Face mount on shaft flange
Axial bolts clamp the solid center of the hub against the shaft flange. Two off-center dowel pins locate the hub and transmit torque between the flange and hub.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Axial bolts clamp the solid center of the hub against the shaft flange. Two off-center dowel pins locate the hub and transmit torque between the flange and hub.
A coil spring pushes the plunger through a guide bore in the hub and into an annular groove in the shaft. Pulling the plunger outward clears the groove and frees the hub to slide along the shaft.
Two tangential screws draw the collar halves together around the shaft. The hub bolts to the collar, and friction at the collar bore transfers torque and resists axial movement.
Each arm carries a flat steel shoe faced with bonded rubber. The belt wraps far enough around the assembly to contact several shoes at once, and friction transfers torque as successive shoes enter the wrapped span.
Rigid end plates connect the cylindrical rim to two sealed ball bearings seated on the axle. The moving belt turns the rim, and the bearings transfer the radial load to the axle.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A curved guide wheel supports the return strand of a narrow belt on a greenhouse seedling tray conveyor. The hub fits over the keyed end of a rotating shaft, and an inward tab at the end of a flexible finger seats in an annular shaft groove. The key transmits rotation, the tab limits axial travel, and lifting the finger clears the groove for wheel removal.
A radial bore in the hub holds a stainless steel ball, a compression spring, and a threaded plug in place of the flexible finger and locking tab. A reduced diameter at the shaft end of the bore retains the ball while allowing it to protrude into the shaft opening. A chamfer on the shaft end pushes the ball outward during installation, and the spring seats the ball in a shallow, rounded shaft groove. Axial pulling cams the ball back into the bore for removal, while a separate key transmits torque between the shaft and the hub.
A molded polyurethane tread ring serves as the belt contact rim and fits over a cylindrical carrier joined to the hub by radial webs. Axial ribs on the carrier fit matching slots inside the tread ring, and a bolted end flange retains the ring against a fixed shoulder. The ribs transmit circumferential force from the hub to the tread, and the tread surface contacts the belt. The flexible finger holds the hub in the shaft groove while removal of the end flange lets the tread ring slide off the carrier.
A 120 mm wide pulley rim surrounds a hub with a 30 mm keyed shaft opening and two flexible fingers at opposite angular positions. Both fingers carry inward tabs that seat in the same 3 mm wide, 1 mm deep annular shaft groove. Each tab projects 0.8 mm into the opening and has 1.2 mm of outward release travel. A two-prong tool lifts both fingers together while the pulley slides along the shaft.
A belt return pulley uses a keyed hub with a flexible locking finger and a curved belt contact rim. Two bearing blocks support the rotating shaft on parallel frame slots, and an adjusting screw moves each block along its slot. Turning the screws by equal amounts shifts the pulley to set belt tension while keeping the shaft square to the frame. After the screws retract the blocks to slacken the belt, one bearing block detaches from the shaft and the pulley slides off that end when the finger lifts clear of the shaft groove.
An assembly fixture holds a keyed shaft with its groove at a fixed axial position and aligns the hub keyway with the shaft key. A servo press advances the hub over the chamfered shaft end, which deflects the flexible finger outward until its tab reaches the groove. A displacement probe measures the finger position through an access window, and the press encoder records the hub position. The controller accepts the assembly when both measurements fall within the ranges for a seated tab and a fully inserted hub.
An injection-molded acetal hub has an integral cantilever finger with an inward tab. A chamfer on the shaft pushes the ramped tab outward during insertion, and the finger springs inward when the tab reaches the annular groove.
Two rivets fasten one end of a spring steel strip to a fixed portion of the hub. The formed tip projects inward into a shaft groove, and the strip bends outward when the tip is lifted for removal.
Radial webs connect the flexible hub to a continuous steel rim covered with bonded rubber. The finished rim has a slightly larger diameter at midspan than at the edges, which helps center a flat belt.
A continuous molded nylon rim connects to the flexible hub through radial spokes and has a circumferential V groove. The sloped groove faces contact the sides of a matching V belt and transfer torque by friction.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In some versions, the threaded opening of the primary locking lug nut extends along a lug axis and the outer face of the primary locking lug nut has a surface disposed in a plane perpendicular to the lug axis, and the key pattern is recessed into the surface.B · US 9,016,096 B2 · ¶ 6
FIG. 1 shows an inventive driving pulley with a rotary vibration damping assembly which comprises a pulley rim 11 for a poly-V-belt and a hub 12 which can be clamped to a generator shaft; the relative rotatable support between the two parts can be effected by a sliding sleeve 13.A · US 2008/0207364 A1 · ¶ 26
An empty cell means only that no passage was reproduced there.
It is therefore an object of the present invention to provide driving pulleys which ensure the disconnection of vibrations within the belt drive.A · US 2008/0207364 A1 · ¶ 6
In such an embodiment, only elastic rotational disconnection between the crankshaft and the generator can occur, both for the delay phase and also the acceleration phase, and without a complete disconnection of the transmission of torque.A · US 2008/0207364 A1 · ¶ 7
The present invention relates generally to a system for locking engagement with a threaded stud such as for anti-theft attachment of a wheel to a vehicle.B · US 9,016,096 B2 · ¶ 2
In light of the above, there is a need for improved locking lug nut systems.B · US 9,016,096 B2 · ¶ 4
patent.fyi, US 2026/0356593 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356593/, SHA-256 e1776f63a1b3d3f329dd3dad90ff488564f61dd37194bed7c773bbd98de302d1