1.1Open tubular carrier frame
Four corner posts connect an upper crossbeam to two lower box-section rails. The crossbeam carries the robot mounting plate, and the lower rails carry the guides for the loading surface.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Four corner posts connect an upper crossbeam to two lower box-section rails. The crossbeam carries the robot mounting plate, and the lower rails carry the guides for the loading surface.
Two ribbed metal trays slide inward on linear guides until their inner edges meet beneath the layer. At the destination, a perimeter restraint holds the products in position while the trays slide outward together and deposit the layer.
A continuous steel deck supports the layer throughout transport. At the destination, the robot aligns the deck with the receiving surface, and a full-width pusher moves the layer across a short bridge plate.
A row of hinged slats rides in straight guides that extend into a side pocket as long as the loading surface. A linear actuator draws the full row into the pocket to clear the opening and pushes it back across the opening for the next load.
One reel pays out the web across the top of the loading surface and around a nose roller, while the other reel takes it up below. During unloading, the reel drives hold the upper span nearly stationary relative to the frame as the loading surface withdraws beneath it.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
An overhead robot carries the frame between a nursery staging bench and a grow rack. The closed-loop belt runs around a flexible loading plane that supports a layer of rigid seedling trays by their bases, and drain slots in the side panels let irrigation water escape. The robot lowers the head until the tray bases sit just above a rack shelf, then retracts the plane horizontally and upward while the belt rolls beneath the trays.
A continuous spring steel sheet forms the flexible loading plane and carries the closed-loop belt around its rounded leading edge. Opposed roller tracks retain both sheet edges, support the horizontal span and guide the sheet through a large-radius bend into a vertical pocket. Synchronized toothed belts attached to the trailing edge move the sheet in both directions. The bend radius keeps cyclic bending strain within the allowable fatigue range of the sheet.
The frame has a 400 by 300 mm lower opening and carries a layer of cartons with a combined mass of up to 5 kg. The loading plane spans the 300 mm width and travels along the 400 mm length before turning upward around a guide with a 75 mm centerline radius. The actuator provides 420 mm of travel, including 20 mm of clearance past the opening, and retracts at 100 mm/s after the robot positions the belt surface 5 mm above the receiving surface.
An overhead gantry carries the gripping head between a rail-guided shuttle and a pallet lift. The shuttle deck uses parallel support rails with slots between them, and the flexible loading plane has a tapered leading edge that feeds beneath a staged product layer after the shuttle lowers its rails relative to the head. A position sensor confirms that the loading plane covers the opening before the gantry lifts the layer clear of the shuttle. At the pallet lift, the head retracts the plane and rolls the belt beneath the layer while the lift maintains the receiving height.
A motorized traction roller engages the belt return run, and a spring-loaded idler takes up slack as the loading plane travels through its guides. An encoder measures loading-plane travel, and an optical surface-speed sensor measures the belt speed relative to the frame on an exposed edge of the upper run. During horizontal withdrawal, the controller drives the belt so the upper contact surface stays nearly stationary relative to the frame. The controller pauses withdrawal when measured surface speed exceeds 10 mm/s for more than 100 ms.
A laser line profiler mounts on the outside of the frame with its scan line below the loading plane. The robot sweeps the profiler over the receiving surface and records each profile with the corresponding robot position to build a height map. The controller sets the release height from the highest measured point within the product footprint and permits retraction when the height variation stays within the configured tolerance. After release, a second sweep checks that the deposited layer reaches the expected height.
Two folded steel side panels bolt to a top crossmember with a machined robot mounting face. Each panel carries a replaceable guide rail that locates the adjacent edge of the flexible loading surface.
The frame defines a rectangular lower opening with 20 mm of clearance on each side of the nominal layer. Before the loading surface withdraws, the robot positions the layer just above the receiving surface to limit the drop.
Hinged aluminum slats carry guide rollers at both ends. Paired tracks guide the slats horizontally across the lower opening and through quarter-circle bends into vertical storage runs.
A polyurethane-coated polyester belt forms a closed loop around the flexible loading surface. A nose roller guides the belt around the moving edge, and a spring-loaded idler tensions the return span below the surface.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
According to a first characteristic disposition, this aim has been achieved with a coiled curtain, in particular a transparent coiled curtain, of the kind featuring a roll-up apron comprising a number of horizontal slats articulated among themselves, by means of joint sections, said apron coiling up on an upper horizontal shaft or drum and its lateral edges are mounted with the ability of moving in vertical slides or guides, this transparent coiled curtain being especially reA · US 2015/0368965 A1 · ¶ 41
The belt connector 30 connects the ends of the belt to form a continuous loop. The belt is configured to be entrained around a plurality of rotatable elements, such as rollers or pulleys.B · US 2017/0247189 A1 · ¶ 17
An empty cell means only that no passage was reproduced there.
Such rollup curtains are generally relied upon to be shaped and fitted to constitute rollup shutters or analog closures, or dividing partitions, or wall portions, or complete partitions of certain locations.A · US 2015/0368965 A1 · ¶ 8
Such curtains permit the view and the passage of light from the inside to the outside and/or from the outside to the inside, and this even when the transparent rollup curtain is in the lowered position.A · US 2015/0368965 A1 · ¶ 9
Therefore, the welding process can create undue down time for machinery.B · US 2017/0247189 A1 · ¶ 3
Such fasteners also tend to creep during use, which frequently causes the connector to become detached.B · US 2017/0247189 A1 · ¶ 3
patent.fyi, US 2026/0356604 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356604/, SHA-256 2fa133f2e36c26aeda88c8d2f90a4fa38c505820421785218e6dc804ac749f75