1.1Single continuous inlet slot
The tube holds the slot upward during discharge while the internal screw rotates. The screw draws material from beneath the slot and carries it axially to an end outlet.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The tube holds the slot upward during discharge while the internal screw rotates. The screw draws material from beneath the slot and carries it axially to an end outlet.
An end sprocket pulls the loaded chain run through the tube, where transverse flights sweep material toward the outlet. The return run travels through a separate enclosed duct beneath the tube.
Two overhead rail carriages suspend the tube from saddles at its quarter points. The carriages move across the silo opening while the overhanging tube ends carry the screw drive and discharge outlet.
A spring-loaded measuring reel at the end of each rail pays out a tensioned cable attached to its carriage. An encoder on each reel reports displacement, and the controller compares the readings after referencing them to a common starting line.
At each sensor crossing, the controller records the carriage coordinate assigned to that station and resets that carriage's incremental displacement count. Between crossings, it adds the signed displacement from a measuring-wheel encoder to the last recorded coordinate and compares the two carriage positions.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A perforated feeder tube spans the underside of a rectangular bin that stores dry crushed glass, and a coaxial screw carries the glass toward one end of the tube. Two powered carriages carry the tube along rails on opposite sides of the bin opening, and a traveling chute drops the glass onto a stationary belt beneath the discharge-side rail. Matched arrival detectors mark equal travel distances on both rails. At each detector pair, the controller holds the carriage that arrives first until the other carriage reaches the matching detector.
Inductive proximity sensors replace contact switches at matched stations along the two carriage rails. Each carriage carries a steel flag that passes within the rated sensing gap of each sensor on its rail. The controller latches each arrival by station number and applies the brake on the first carriage to report that station. The controller releases the brake when the opposite carriage reports the same station.
A single brake motor on one carriage replaces the independent travel drives and turns two pinions through a cross shaft supported on the moving frame alongside the feeder tube. Each pinion meshes with a longitudinal rack fixed to its rail, and the pinions have the same pitch diameter so one shaft revolution advances both carriages by the same distance. The racks are phased with the feeder tube square to the rails, and shaft stiffness and gear backlash set the maximum relative motion under load. Paired rail sensors monitor arrival timing, and the controller applies the common brake if the second arrival falls outside a set time window.
Each rail provides 4 m of travel, and paired arrival stations sit 80 mm apart through the central 3 m and 40 mm apart through the final 0.5 m at each end. The controller uses a 100 mm travel difference limit and restricts carriage speed to 40 mm/s in the center and 20 mm/s in the end zones. Detection, drive response and braking together limit travel after an arrival signal to 10 mm at either speed. The controller starts each stroke with both carriages at a common reference station and holds the leading carriage at each successive station until its mate registers.
The feeder tube discharges through a carriage-mounted chute onto a gathering belt that runs parallel to the discharge-side rail. The gathering belt transfers material into a surge hopper above a weigh belt feeder, which uses belt load and speed to regulate the downstream mass flow. A level transmitter in the hopper signals the conveyor controller to pause tube travel and screw rotation at the upper setpoint and resume them at the lower setpoint. The controller retains the arrival state of both carriages during the pause and completes any pending station alignment before advancing to the next pair.
A magnetic linear scale runs along each rail, and a carriage-mounted read head reports absolute position from a common transverse datum. The controller converts both positions to distance traveled in the current direction and samples the difference every 10 ms. It trims the speed of the leading carriage as the difference grows and commands that carriage to stop at a configured threshold below the travel difference limit. The threshold reserves distance for sampling delay and braking, and the controller restores normal speed after the difference falls below a lower restart threshold.
A geared motor turns the inlet tube through a ring gear attached to an end collar. A separate geared motor turns the coaxial screw through its shaft, and separate bearings support the collar and shaft.
A flanged-wheel carriage supports each tube end and rolls on a rail beside the silo opening. A geared motor on each carriage turns a pinion that engages a fixed rack parallel to the rail.
Inductive proximity switches mount at matching coordinates on the two rails, and a steel flag on each carriage passes within sensing range of its switches. The stations have a 25 mm pitch for a permitted travel difference of 40 mm.
When a first-side switch signals arrival, the controller stores its station index and commands the first drive to stop and hold position. The controller releases the hold when the second carriage registers arrival at the same index, and the station pitch and stopping distance fit within the travel difference limit.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Grain storage bins often include a grain bin unload trough conveyor under the bin floor that conveys material from within the grain bin to the exterior of the bin through the use of a conveying auger enclosed within a formed metal trough. An internal bin sweep conveyor located above the bin floor can be paired with such an unload trough conveyor to help convey grain inside the bin into the unload trough conveyor through control gates.B · US 2024/0208735 A1 · ¶ 4
It is worth noting that, referring to FIGS. 9 and 11, the cutting machine 10 includes a cutter structure 1, a travelling carriage assembly 2, and motors for driving the travelling carriage assembly 2 to move along the X and Y axes, and a corresponding connecting structure.A · US 2024/0001574 A1 · ¶ 51
The travelling carriage assembly 2 further includes a detecting element 3 which is arranged corresponding to the reflecting plane 181 so that when the cutter structure 1 is rotated to drive the reflecting plane 181 to a predetermined position, the detecting element 3 can detect light reflected by the reflecting plane 181.A · US 2024/0001574 A1 · ¶ 48
An empty cell means only that no passage was reproduced there.
However, in the conventional rotary cutting machine, when the motor fails and needs to be replaced, due to that the cutter is connected to the motor through the transmission structure, the transmission structure and the cutter need to be removed first, and then the cutting machine is disassembled to remove and replace the motor, which is complex in operation.A · US 2024/0001574 A1 · ¶ 5
The auger should be held in a centered position within the trough to maintain a proper gap between the rotating auger flight and the walls of the trough.B · US 2024/0208735 A1 · ¶ 5
The auger hanger can extend down to hold the auger shaft in the conveyor trough centrally within the first interior lateral width between the lower portions of the side walls.B · US 2024/0208735 A1 · ¶ 8
patent.fyi, US 2026/0356607 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356607/, SHA-256 63983ad5d5b2f5da013d4334b14d0598aba07e184896eb35cb417616aa00f1c7