1.1Vertical spindle feed
Tubular articles stack around a spindle with a downward-facing discharge end. An upper gate holds the remaining stack while a lower gate releases the bottom article into a receiving cradle.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Tubular articles stack around a spindle with a downward-facing discharge end. An upper gate holds the remaining stack while a lower gate releases the bottom article into a receiving cradle.
Opposed powered belts grip the outer surfaces of the articles and move them at constant axial speed. An encoder on the belt drive synchronizes a traveling gripper with each leading article so the gripper lifts it clear while the remaining articles keep moving.
A square steel bar bolts to the rear frame, and bearing cartridges clamp to its flat faces at two axial stations. Rollers in the cartridges contact the inside of the surrounding tube and support its rotation about the centerline of the bar.
A dowel locks the sleeve to the shaft, and low-friction polymer wear strips support the article bores. Pusher fingers travel through longitudinal slots in the sleeve and advance the articles by one feed increment per cycle.
A frame-mounted linear guide carries an overhead carriage with a broad shoe that contacts the upper part of the rearmost article's end face. A lead screw moves the carriage forward by the programmed feed increment, and the end faces transmit the thrust through the row.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A horizontal spindle holds a row of rigid packaging sleeves ahead of a labeling station. A freely rotating tube surrounds the fixed shaft and carries circumferentially spaced sliding transfer elements with pads that grip the sleeve bores. An axial actuator advances the extended pads by one sleeve length, then retracts the pads before returning them. A receiving mandrel supports the discharged sleeve and rotates it under a label applicator.
Three narrow timing belts replace the axially sliding transfer elements and sit in longitudinal recesses spaced around the rotating tube. Each belt runs around two pulleys with its outer run parallel to the spindle axis and covered with a friction facing. A motor mounted on the tube drives the three rear pulleys through a common ring gear, and a rotary electrical joint supplies power across the fixed shaft and rotating tube. The motor indexes the belts by one article length per cycle, and the outer runs carry the articles toward the spindle tip.
Spring-mounted vacuum shoes with elastomer sealing lips replace the article-contacting transfer elements on a spindle for smooth, nonporous tubes. Axial carriages carry the shoes at circumferentially spaced positions, and flexible lines connect them to a manifold supplied through a rotary vacuum union. Each shoe has a sealing footprint shorter than the shortest tube and sits within a tube bore during the gripping stroke. The actuator advances the carriages after vacuum reaches a preset threshold, then the manifold vents and a cam retracts the shoes for the return stroke.
A 200 mm usable spindle length holds twenty spacer rings with a 30 mm bore and an axial width of 8.0 ± 0.1 mm. Four transfer elements spaced 90 degrees apart carry spring-backed pads that extend against the ring bores, and a servo actuator provides an adjustable axial stroke of 7.5 to 8.5 mm. At 30 cycles per minute, the pads grip, advance the column, release, and return while a releasable brake holds the column during the return stroke. A gap sensor at the outlet confirms when the trailing face of the leading ring clears the spindle tip and ends the forward stroke.
The spindle faces a horizontal receiving nest on the edge of a vertical rotary indexing table. During each table dwell, the nest aligns coaxially with the spindle tip, and the transfer elements advance the leading tube into the nest. A fixed stop locates the tube against its front face, and a spring clamp closes on its outside diameter. The table advances only after a seating sensor confirms tube position and an actuator switch confirms that the transfer elements have returned.
A laser profile sensor mounted above the discharge end looks through a narrow slot in the external guide and measures the axial positions of the leading tube's end faces. A controller uses those positions to compute the travel needed for the trailing face to clear the spindle tip and sends that target to an encoder-equipped linear actuator. An opposed photoelectric sensor at the outlet confirms passage, and the controller inhibits the next cycle until the downstream receiver reports that it is empty.
A cantilevered spindle extends rearward from the frame, and an axial pusher moves the articles toward the front. At the pickup position, a short front spindle section withdraws into the frame while a gripper holds the leading article and lifts it sideways.
A machined pilot on the rear flange locates the horizontal spindle in a frame plate, and four bolts clamp the flange to the plate. The free front end carries a tapered lead-in that centers each article bore during replenishment.
A servo motor turns a ball screw whose nut drives the thrust carriage. The controller sets each indexing stroke to the nominal axial length of an article and holds the carriage in position during pickup.
Two sealed deep-groove ball bearings support the outer tube coaxially on the fixed cylindrical shaft. Shaft shoulders and retaining rings locate the bearings axially while the tube rotates under contact with the article bores.
Three spring-retracted fingers sit 120 degrees apart on a sliding carrier guided by the cylindrical shaft. A cam raises the fingers through axial sleeve slots to engage the rear article face, and a thrust actuator advances the carrier before the fingers retract for the return stroke.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
According to the disclosure, the mechanical multiple torque damping device is connectable with an end of a horizontal spindle, and includes a support module, a spindle coupling sleeve and a damping cylinder.B · US 2023/0025616 A1 · ¶ 6
In the first aspect, it is preferable that the first lens drive section and the second lens drive section each comprise a stepping motor, the first counter counts, as the amount of feed, the number of drive pulses from the control section to the first lens drive section corresponding to stepwise driving of the first zoom lens by the first lens drive section, and the second counter counts, as the amount of feed, the number of drive pulses from the control section to the secondA · US 8,508,584 B2 · ¶ 15
The tubular support axle is securely connected with the base wall and extends from the inner wall surface to have a terminal end.B · US 2023/0025616 A1 · ¶ 6
The spindle coupling sleeve is rotatably and coaxially sleeved on the tubular support axle and adjacent to the base wall.B · US 2023/0025616 A1 · ¶ 6
An empty cell means only that no passage was reproduced there.
The present invention relates to an image pickup apparatus including a plurality of optical systems and, more particularly, to rectification of a discrepancy in zoom factor among the optical systems.A · US 8,508,584 B2 · ¶ 2
Thus, it is desired to vary the resisting force during the lowering process so as to bring the shade down smoothly and steadily.B · US 2023/0025616 A1 · ¶ 3
Therefore, an object of the disclosure is to provide a mechanical multiple torque damping device that can generate multiple frictional torques during a rotation stroke to alleviate at least one of the drawbacks of the prior art.B · US 2023/0025616 A1 · ¶ 5
patent.fyi, US 2026/0356615 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356615/, SHA-256 4f975717a8428af28fa8e06024950bec02b66bf6c00d9e268c27f6e1075f8f43