1.1External tape level pointer
A spring-loaded follower roller rides on the outer wrap of the tape roll. As the roll diameter decreases, the follower arm turns a shaft that carries a pointer across a scale on the outside of the housing.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A spring-loaded follower roller rides on the outer wrap of the tape roll. As the roll diameter decreases, the follower arm turns a shaft that carries a pointer across a scale on the outside of the housing.
A rubber-coated measuring wheel and a spring-loaded idler pinch the tape near the outlet. A rotary encoder counts wheel motion, and a counter converts the net count to millimeters from the point where the operator presses reset.
A 16 mm diameter bore with a rounded rim passes 12 mm tape at its full width. A flanged guide roller just inside the bore centers the tape so its edges clear the rim.
A smooth polymer sleeve is keyed to a stationary spindle fixed to the housing. The spool bore slides over the sleeve and turns on it as tape pays out, while a retaining washer limits axial movement.
The operator draws the selected length from the housing and lays the intended cut point across the bench cutter's anvil. A lever lowers a blade through the tape and into a groove in the anvil.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A benchtop housing holds a roll of gummed paper tape on a freely rotating spindle visible through a transparent window. The tape exits a horizontal slot beside a ruler marked on the housing, with zero at the cut line. A lever closes a pair of pivoting shear jaws across the tape after the operator pulls the free end to the desired graduation. The operator wets the cut strip and applies it to the back of a picture frame.
A tensioned stainless steel wire replaces the cutter beside the dispensing slot of a windowed spool housing. A pivoting lever carries the wire across the full tape width and presses it into a shallow groove in a rigid anvil. The operator draws the tape against the housing scale, holds the free end taut, and depresses the lever to sever the tape.
Two parallel idler rollers support the spool by its outer flange rims in place of a central spindle. The rollers turn on fixed axles inside a transparent-window housing, and side plates keep the spool centered over the rollers. The dispensing slot sits below the spool axis so the tape leaves the underside of the roll and the pull keeps the spool seated in the cradle. The operator measures the tape against the housing scale and closes the shear beside the slot.
A housing contains three independently rotating spool hubs for tape widths of 12, 19, and 25 millimeters. Each hub aligns with a separate dispensing slot that provides 1 millimeter of clearance on each side of the tape. One transparent window spans all three spools, and a 150 millimeter scale beside each slot starts at the cut line. A separate lever shear at each slot cuts the selected tape without moving the other spools.
A windowed tape housing bolts to the side frame of a manual carton sealing station, with its dispensing slot facing the work surface. A rotating hub carries a pressure-sensitive tape roll, and the slot presents the tape with its adhesive side toward the carton. The operator reads the length against the housing scale, presses the free end onto the carton, and uses the shear beside the slot to separate the strip. A rubber roller mounted on the station presses the strip onto the carton seam.
A stepper motor drives a feed roller and a spring-loaded idler presses tape against it upstream of the dispensing slot. An encoder on a separate measuring wheel reports tape travel to a controller as tape unwinds from a rotating spool visible through the housing window. A movable stop beside the housing scale sets the requested length, and a linear position sensor reads the stop position. The controller stops the feed at the corresponding encoder count and drives a solenoid to close a shear beside the slot.
A 1.5 mm clear polycarbonate insert snaps into an opening in the housing sidewall. The opening exposes a radial section of the spool so the operator can see the outer edge of the remaining tape.
A molded measuring line follows the curved outer wall from the dispensing slot. Tick marks at 5 mm intervals measure distance along the curve, and the operator lays the tape against the wall to read its length.
A polymer hub carries the spool on three flexible ribs that grip its bore. Two sealed ball bearings support the hub on a steel axle, and a retaining clip holds the hub in position along the axle.
A spring-return slider carries a stainless steel blade directly beside the dispensing slot. Pressing the slider drives the blade through the tape against a polymer anvil, and releasing it retracts the blade into a guard.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The viewports 144, when present, may be transparent portions inserted into the material forming the spool housing 104′ or may be merely voids in the spool housing, and may be of any number, orientation, shape, or arrangement. The viewports 144 may allow visual inspection of the spool 102′ and/or fishing line 114′ within the spool housing 104′.A · US 2008/0203207 A1 · ¶ 32
The spool is inserted into the spool housing. The spool is rotatably supported within the spool housing.A · US 2008/0203207 A1 · ¶ 5
A handheld dispenser of pressure sensitive adhesive tape comprising a handle and a rotating spool holder including a brake plate and holding a roll of pressure sensitive adhesive tape on the tape spool holder, and a cutting blade, an idler pulley, and a finger activated trigger stopping the motion of the tape supply reel by engaging the brake plate through actuating a lever coupling the brake plate and the trigger, thus stopping the dispensing of tape when the trigger is presB · US 9,670,028 B1 · abstract
The user then exerts force to stretch the tape over the cutting blade 19 to cut the tape.B · US 9,670,028 B1 · ¶ 38
An empty cell means only that no passage was reproduced there.
Two people are needed to wind the fishing line onto a fishing reel.A · US 2008/0203207 A1 · ¶ 3
Tension of the unwound fishing line is controlled by controlling rotation of the spool.A · US 2008/0203207 A1 · ¶ 5
All too often, if the balance of pressure and the angle is not correct, the result is the tape cut being longer than the desired length or a cut that is frayed by the jagged cutting blade.B · US 9,670,028 B1 · ¶ 4
With too little tension, the tape roll continues spinning after the cut because of the sudden loss of tension.B · US 9,670,028 B1 · ¶ 6
patent.fyi, US 2026/0356618 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356618/, SHA-256 742821b21ec7a55432460ffe560a3efefac3d34b31c803b7da7fa17a0b002be0