1.1Floor-mounted payout stand
The stand supports the reel on a horizontal shaft. A pull cable draws the leading link along the roller chute and into the conveyor track.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The stand supports the reel on a horizontal shaft. A pull cable draws the leading link along the roller chute and into the conveyor track.
A gearmotor turns a feed sprocket whose tooth spacing matches the chain pitch. A guide holds the chain in mesh with the sprocket and directs it into the track.
The valve meters oil to a hydraulic motor that drives a sprocket engaged with the chain. Changing the metered flow changes the sprocket speed and the chain feed rate.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A lift frame carries a braked reel wound with steel drag chain for a sawdust conveyor. The frame hangs above the open trough, and a steel guide chute spans the gap between the reel and the trough entrance. The installer releases the hub brake and adjusts braking torque as the chain enters the trough. A hand winch draws the leading link along the trough until the last links clear the reel and enter the track.
A steel disc keyed to the reel shaft runs between the pads of a spring applied hydraulic caliper bolted to the lift frame. A hydraulic power pack supplies release pressure through an adjustable pressure reducing valve, and a dump valve connects the caliper to the reservoir. Increasing caliper pressure reduces pad force and starts or accelerates payout, while reducing pressure increases pad force and slows payout. A hand winch pulls the final links into the track, and opening the dump valve clamps the reel disc.
A chain drive couples the reel shaft to a fixed displacement hydraulic pump mounted on the lift frame. The pump draws oil from a reservoir and discharges through an adjustable flow control valve, with a pressure relief valve set above normal operating pressure. Opening the flow control valve releases the hydraulic braking load enough to start payout, and adjusting the opening changes pump flow and reel speed as a puller draws the chain into the track. After the puller feeds the last links into the track, a spring applied shaft brake holds the reel stationary.
An overhead hoist lifts a frame carrying a 300 mm core reel loaded with 12 m of conveyor chain at 25 mm pitch. A roller guide mounted 150 mm below the reel axis directs the chain into the track entrance. The installer releases the hub brake and adjusts it to hold the first 11 m of payout at 0.10 m/s while a hand winch draws the chain along the track. A mark 1 m from the trailing end signals the installer to increase braking and reduce payout to 0.03 m/s until the last link enters the track.
A lifted reel frame feeds chain into one end of the conveyor track, and a powered capstan anchors beside the opposite end. A pulling rope runs through the track and connects to the leading chain link through a clevis sized to pass through the track guides. The installer releases the hub brake and adjusts braking torque during the pull to keep the chain taut between the reel and the track entrance. The capstan pulls the final links through the entrance and stops when the leading link reaches the joining station.
A lift frame carries the reel and a spring applied brake released by a proportional hydraulic valve. An encoder on a pinch roller at the track entrance measures chain travel, and a powered puller draws the leading link through the track. A controller increases brake release pressure when measured speed falls below the setpoint and reduces pressure when measured speed rises above it. A trailing end sensor upstream of the entrance commands a lower speed for the remaining links, and the controller stops the puller after the encoder measures enough travel for the last link to clear the entrance.
Flanged rollers support the chain and keep it aligned during payout. Once the chain is fully off the reel, a winch draws it from the roller table through a guide at the track entrance.
An operator selects the feed speed before starting a gearmotor. The motor drives a fixed-pitch sprocket at a constant shaft speed through the dispensing run.
Temporary saddles hold the remaining links at their installed elevation. Split track sections bolt around the chain, and the saddles are withdrawn after the track takes its weight.
Four sling legs connect a crane hook to lifting lugs welded to the steel support frame. Sling leg lengths position the loaded center of gravity under the hook and keep the reel shaft horizontal during the lift.
A spring-applied caliper grips a steel disc keyed to the reel shaft. A hand lever retracts the caliper pads so a pull cable can draw the chain off the reel and into the track.
A pressure regulator supplies a pneumatic caliper on the reel shaft disc. The operator raises caliper pressure to slow payout and lowers it to increase the feed rate.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The tensile force-related information is information that is related to tensile force acting on a fishing line and detected during a fishing line discharge period in which the fishing line is released from a dual-bearing reel configured to brake rotation of a spool based on a braking parameter.B · US 2020/0165109 A1 · abstract
The passive system uses a dynamically controlled drag brake on the material spool shaft, and a dancer roll mounted on a dynamically controlled linear slide. The force exerted on both the brake and the dancer roll slide can be continuously varied by a control system.A · US 2017/0101286 A1 · ¶ 4
The tensile force-related information is information that is related to tensile force acting on a fishing line and detected during a fishing line discharge period in which the fishing line is released from a dual-bearing reel configured to brake rotation of a spool based on a braking parameter. The braking parameter correction unit is configured to correct braking parameters based on temporal changes in the tensile force-related information acquired by the tensile force-related information acquisition unit.B · US 2020/0165109 A1 · abstract
An empty cell means only that no passage was reproduced there.
The device relates to a system for passively controlling the tension of tow as it is paid out from a creel to a composite placement head.A · US 2017/0101286 A1 · ¶ 1
It is not possible at the low tensions used in the fiber placement process to control passive units sufficiently to buffer rapid tow acceleration and deceleration changes and resulting spool inertial loads with fine enough resolution for the fiber placement process.A · US 2017/0101286 A1 · ¶ 3
That is, it is difficult to achieve a setting for spool braking of a fishing reel that is in accord with the preferences of each individual user by the technique disclosed in Japanese Published Unexamined Application No. 2014-357601.B · US 2020/0165109 A1 · ¶ 4
It thereby is possible to achieve a setting for spool braking of a fishing reel that is in accordance with the preferences of each individual user.B · US 2020/0165109 A1 · ¶ 7
patent.fyi, US 2026/0356621 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356621/, SHA-256 0ce3bd94e9c13394fb2b0a4b66701633ffb0fdcbf7ee3161281dd9d69e189457