1.1Base with sliding pads
Four nonrotating polyethylene pads carry the load at the corners of the base. Rounded pad edges glide over floor joints when the user pushes the rack.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Four nonrotating polyethylene pads carry the load at the corners of the base. Rounded pad edges glide over floor joints when the user pushes the rack.
Two aluminum tubes rise from opposite sides of the base and meet at an apex above its center. A gusset joins the tubes and carries the horizontal member, and triangular foot plates transfer the load to the base.
A mandrel bend turns the upper end of the steel tube through 90 degrees. The uninterrupted tube wall transfers the load from the horizontal run into the upright.
A dovetail slide on the horizontal member guides the support structure toward or away from the user. The dovetail faces constrain rotation, and a thumb screw clamps the slide at the selected position.
A saddle fixed to the bottom of the post spans the full width of a solid base slab. Two screws draw opposing jaws against the slab edges, and broad saddle pads bear on the upper face to resist rocking.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A wheeled base carries a vertical post and a horizontal arm that reaches over a packaging bench. A pivot at the end of the arm lets the support bar swing parallel to the bench edge. Each underside socket accepts a removable spool yoke with a horizontal spindle and a felt drag washer. The operator draws ribbon through a guide eye below each spindle, and the drag washer limits spool overrun after cutting.
A continuous aluminum T-slot rail replaces the discrete receiving points on the underside of the pivoting support. Each bobbin holder bolts to a spring-loaded T-nut that fits into the rail slot. Loosening the bolt lets the holder slide along the rail, and tightening it clamps the holder at the selected spacing.
A 420 mm by 500 mm base with four 50 mm casters carries a 750 mm post and a horizontal arm with a 150 mm reach. A 360 mm support bar pivots about its center on a vertical pin at the end of the arm. Six underside sockets sit on 55 mm centers and accept holders for bobbins up to 45 mm in diameter and 100 g each. Stops limit the bar to 30 degrees of rotation in either direction from its position across the base.
A wheeled bobbin rack docks against the frame of a narrow handloom with two toggle clamps. Its post and horizontal arm carry a pivoting support bar above the loom's rear thread guides, with bobbins suspended from the underside. Each yarn end passes through a ceramic eye and an individual disc tensioner before entering its assigned heddle and reed dent. Rotating the bar at the arm aligns the row of bobbins with the loom's entry guides.
Each underside receiver on the pivoting support carries a strain-gauge load cell between a fixed bracket and the bobbin holder. A controller mounted on the support samples each cell after its readings settle and subtracts the stored mass of the empty holder and spool. The controller divides the resulting yarn mass by the entered mass per meter to estimate remaining length. A display on the post shows each estimate, and an indicator beside the holder lights below a user-set threshold.
The pivoting support bar carries an indicator beside each underside bobbin socket, and a controller on the post stores the mapping between pattern colors and socket positions. The controller reads a stitch grid from a removable memory card and groups adjacent cells of the same color in the active row. A foot pedal advances the controller to the next group, and a second pedal returns it to the previous group. The controller lights the corresponding socket and shows the stitch count on a display.
Upward-facing threaded studs on the top surface accept flanged bobbin holders secured by hand nuts. Each holder carries a spindle that lets its bobbin turn independently as yarn pays out.
Four 50 mm swivel casters bolt to the corners of a steel base plate. A round socket welded at the center of the plate receives the lower end of the post.
The lower tube slides into the base socket and is retained by a cross pin. A spring-loaded button on the inner tube engages holes in the lower tube at 25 mm intervals to set the height.
A split aluminum collar wraps around the vertical post and carries a bolted rectangular arm. Loosening the collar screw lets the arm move up or down and turn around the post before the collar is tightened.
A vertical shoulder bolt joins the support bar to the horizontal member, and a spring-loaded pin engages a row of holes around the bolt to set the bar angle. Threaded inserts along the underside accept screws that secure the bobbin holders.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In the embodiment shown, the receptacles are openings arranged in the rearward end of base bars 250 attached to the bottom of each of the vertical support members 112, 114. The base bars 250 preferably extend a predetermined distance from the forward side of the vertical support members 112, 114 to provide a stable base for the display system 100.A · US 2014/0251841 A1 · ¶ 41
The post support 14a includes a post socket 22 having an internal cavity 23 and an open top 24.B · US 2016/0208504 A1 · ¶ 23
In the embodiment shown, the receptacles are openings arranged in the rearward end of base bars 250 attached to the bottom of each of the vertical support members 112, 114.A · US 2014/0251841 A1 · ¶ 41
The lower ends of posts are then inserted into the post sockets to support the posts above the concrete floor and rails are supported on the posts.B · US 2016/0208504 A1 · ¶ 2
A kit to make a projection and display frame, the kit comprising: a pair of foldable vertical support members that can be unfolded to form vertical support members; a top horizontal support member configured to join to each of the pair of vertical support members near tops of the vertical support members; a lower horizontal support member configured to join to each of the pair of vertical support members below the top horizontal support member; an adjustable boom configured tA · US 2014/0251841 A1 · claim 21
The horizontal member 68 in this example has a generally triangular shape and is connected to the body 17 by welding.B · US 2016/0208504 A1 · ¶ 25
An empty cell means only that no passage was reproduced there.
Nos. 7,290,888 and 6,736,516, for example, may be more complex to set up, take down, store, and transport, may be harder to adjust, and may not be as sturdy or stable as is desirable.A · US 2014/0251841 A1 · ¶ 2
More particularly, this disclosure relates to a portable projection and display system that permits easy setup and take down of the display stand and further facilitates easy adjustment of the projection and display components.A · US 2014/0251841 A1 · ¶ 1
The present invention relates to a safety railing and, in particular, to a safety railing for building construction.B · US 2016/0208504 A1 · ¶ 1
The bar intersects with the anchor and restricts movement of the anchor relative to the post socket.B · US 2016/0208504 A1 · ¶ 3
patent.fyi, US 2026/0356622 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356622/, SHA-256 9e078706460e724c3d4c34af26fcea279ef78f2ebaccc1ba1ddf76b685785ac8