1.1Removable keeper ring
Two hinged ring halves latch around the outermost turns after winding, and inward fingers overlap the free side of the pack. The installer removes the ring after seating the spool in a feeder with a side guide.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Two hinged ring halves latch around the outermost turns after winding, and inward fingers overlap the free side of the pack. The installer removes the ring after seating the spool in a feeder with a side guide.
The tab slides into a molded dovetail guide until a spring latch engages a notch in its edge. Pressing the latch clears the notch so the operator can slide the tab out with the wire end still held in its hole.
A narrow breakaway web joins the tab to a boss on the drum end face. The tab projects through a flange notch with clearance on all sides, and bending the exposed tab fractures the web to release the wire end.
A stainless steel leaf clip seats beneath molded rails and presses against a shallow groove in the tab face. The operator pushes the wire sideways under the clip until it seats in the groove and lifts the clip to free it.
A flexible strip crosses the wire and bonds to flat pads on both sides of it. A folded pull end lets the operator peel the strip back and free the wire before feeding.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A drum between two flanges carries coiled irrigation microtubing, and a breakaway tab on the first flange has a round through-hole. The tubing end passes through the hole and fits over a removable barbed plug whose head is wider than the hole. At installation, the operator bends the tab at its attachment, pulls out the plug, and slides the detached tab off the tubing.
A stamped steel strip with a deburred round hole replaces a molded tab on the first flange. A shallow pocket in the flange locates the inner end of the strip, and a nylon shear pin passes through aligned bores in the strip and pocket walls. The wire end hooks through the exposed hole, and a radial pull on the strip shears the pin and releases the tab.
A die-cut kraft fiberboard strip with a round punched hole replaces a molded tab on the first flange. The strip overlaps the flange face near its rim, and two brittle adhesive dots bond the overlap while the hole projects beyond the rim. The wire end hooks through the hole during handling. The operator folds the strip away from the flange face to fracture the adhesive bonds and free the tab.
A spool has a 100 mm drum diameter and three breakaway tabs spaced 120 degrees apart around a 200 mm first flange. Each tab has a 3 mm round through-hole centered 8 mm beyond the flange perimeter. For 1.0 mm wire, the winding machine indexes the spool to the nearest tab before a guide bends the free end through the hole.
A motor-driven wire feeder has a spool spindle, an inlet guide, and a hinged tab-release lever mounted beside the first flange. The operator rotates the spool until the tab seats in the lever slot, then clamps the exposed wire end in a spring clip beside the inlet guide. Closing the lever bends the tab until its attachment fractures and holds the detached tab in the slot. The operator unhooks the wire from the tab and threads it through the inlet guide to the feed rolls.
A winding station uses a camera facing the tab face, a servo-driven spindle, and a two-axis wire guide with a forming finger. After winding, the station clamps and cuts the wire, then rotates the spool until the camera locates the center of the tab hole. The guide aligns the retained end with the measured center and feeds it through the hole. The forming finger bends the protruding end against the tab face before the clamp opens.
Rounded steel bars mount in sockets in both flanges and contact the innermost turns of wire. The bars sit close enough together to keep the wire from sagging into the gaps under winding tension.
A thin-wall steel tube forms the drum between two molded polymer flanges. Annular sockets in the flanges seat over the tube ends, and circumferential crimps secure the tube to the sockets.
Two thin polypropylene webs join the tab to the outer edge of the first flange. Reduced sections at the flange ends of the webs concentrate strain when the operator bends the tab outward.
A round bore through the tab has a chamfer at the insertion face. A 2.0 mm bore accepts a 1.2 mm wire end, which bends back over the far face to hold the last turn.
An oblong hole extends through the tab and has rounded ends. Its long dimension gives a pre-bent wire end room to pass through at an angle, and rotating the wire seats the bend against the far face.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Based on the foregoing, a need exists for a spool or knockdown reel comprising two flanges and a barrel disposed therebetween that may be efficiently assembled and disassembled.A · US 2008/0078858 A1 · ¶ 15
The termination part 50 further includes a collar 72 coupled to the distal end 60 of the main body 56 by a frangible web 74 to provide torque control during assembly of the termination part 50 on the fastener 40.B · US 2019/0301513 A1 · ¶ 29
An empty cell means only that no passage was reproduced there.
The present invention is directed to a spool on which continuous-strand products such as insulated or bare wire, cable, textile yarns, cordage, chain, etc. are wound.A · US 2008/0078858 A1 · ¶ 3
More particularly, the present invention provides a mechanism for the assembly and disassembly of a knockdown reel in an efficient manner comprising a device for securely fastening and easily unfastening the flanges to the barrel.A · US 2008/0078858 A1 · ¶ 3
For example, fastener sparking modes must be designed for lightning conditions that include hot particle ejection and arcing between the fastener and surrounding structures.B · US 2019/0301513 A1 · ¶ 2
In another aspect of the disclosure that may be combined with any of these aspects, the setback distance is sufficient to prevent arcing between the exposed portion of the metallic core and the threaded portion of the fastener.B · US 2019/0301513 A1 · ¶ 6
patent.fyi, US 2026/0356627 A1, claim 1, first published 2026-11-20T04:17:34-05:00, https://patent.fyi/US20260356627/, SHA-256 38853c3b833265add1e2941b44c870717beaed58876b434b2c450a8e29ea7456