1.1Three sliding neck jaws
Three jaws sit 120 degrees apart in radial guideways. An axially driven cam ring advances all three by the same distance, and return springs retract them for transfer.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Three jaws sit 120 degrees apart in radial guideways. An axially driven cam ring advances all three by the same distance, and return springs retract them for transfer.
Contoured arm pads close on the exposed land and transmit capping torque through friction. The bague rests on a separate ring seat that carries the axial force from the capping head.
Each arm bolts to a carriage on a transverse guide rail. Opposed racks mesh with a common pinion that moves both arms equal distances in opposite directions.
The blocks mount at an included angle of 90 degrees so their inward faces locate the neck at two points. Raised teeth on their upper faces bear against the underside of the bague and resist rotation as the cap tightens.
A molded polyurethane strip sits flush with the upper bearing face of the arcuate support. Downward force from the capping head presses the bague into the strip, and friction at that interface resists rotation.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A pair of hinged arms grips the neck of a detergent refill bottle immediately below its annular collar. An arcuate pocket beneath the arms carries upward teeth that project through recesses in the arm tips and seat against the underside of the collar. An overhead chuck screws on a dispensing closure while the arms resist bottle rotation and the teeth carry the downward load.
Two opposed sliding jaws replace the hinged gripping arms and travel on parallel linear guides fixed to the support. A double-ended lead screw with left-hand and right-hand threads moves the jaws symmetrically toward or away from the neck. Slots open at the inner edges of the jaws and extend along the direction of travel, letting fixed teeth on the lower arcuate pocket enter the slots as the jaws close. The teeth support the collar from below while the jaw faces hold the neck.
Machined acetal tooth inserts replace teeth formed as part of a stainless steel arcuate member. Each insert fits into a vertical slot in the member, seats on a load-bearing shoulder, and is retained by a screw accessible from below. The insert tops project through recesses in the hinged arm tips and provide flat bearing faces with rounded edges beneath the collar. The shoulders transfer the spindle load into the steel member while the screws retain the inserts during bottle transfer.
For a bottle with a 48 mm neck and a 58 mm collar, a lower arcuate member defines a 49 mm diameter pocket with a 50 mm wide flared entrance. Four teeth project upward through two recesses in each hinged arm, with all four tooth centers on a 53 mm pitch circle. Each tooth has a 3 mm radial by 4 mm tangential bearing face, and the four faces lie in a common plane beneath the collar. The arm tips retain the neck while the four faces share the downward load from the capping head.
A continuous rotary capper carries one neck holder on its lower turret directly beneath each overhead capping spindle. Each holder has two hinged arms and a lower arcuate pocket with teeth that rise through recesses in the arm tips. A synchronized infeed star wheel transfers each bottle laterally into the pocket, and a stationary cam closes the arms through a follower on the rotating turret. A second cam opens the arms after capping so an outfeed star wheel can collect the bottle.
Two miniature compression load cells sit between the arcuate member and its mounting bracket, one beneath each side of the neck pocket. A servo closes the hinged arms until motor current reaches a preset gripping threshold, and an encoder checks that the final arm spacing matches the bottle format. The capping spindle applies a low axial preload through the closure, and the controller compares the readings from both load cells with limits established using correctly seated bottles. The controller starts the torque cycle when both readings are within limits and diverts the bottle at the outlet when either check fails.
Each gripping arm carries a screw-mounted acetal insert machined to match the neck radius below the bague. An adjustable closing stop sets the minimum gap between the inserts.
Each arm fits between two lugs on the pliers support. A hardened stainless steel pin passes through both lugs and a flanged bronze bushing pressed into the arm.
A hardened stainless steel arcuate element has two groups of integral teeth machined into its upper face. Flat tooth crests share a common height and support the lower face of the bague.
A slot milled through each arm end opens toward the neck pocket and receives one tooth group. The slot follows the tooth group's path relative to the arm during closing, with clearance for assembly tolerances.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The bottle neck 65 typically includes an enlarged portion (e.g., rim or flange) above the portion of the bottle neck that engages with and moves the distal ends, such that the bottle will be vertically supported by the grip parts 42, 44, and the distal ends 54, 56 partially surround the bottle neck to provide a degree of lateral retention of the bottle neck in the mouth 60.A · US 2020/0148523 A1 · ¶ 24
The first gripping device 310 is shown with a first pair of actuators 312, 314. In operation, each of the first pair of actuators 312, 314 forces a respective gripping jaw into engagement with a surface of a drill stem segment, or removes the respective gripping jaws from contact with the drill stem segment.B · US 12,258,818 B2 · ¶ 17
As shown in the attached FIGS. 1-12, a bottle neck gripper 10 includes jaw components 12 and 14, where jaw component 12 is pivotal about an axis 16 and jaw component 14 is pivotal about a separate axis 18. To facilitate such pivotal movement, each component is mounted to a support plate 20 via respective pins 22, 24 that pass through openings 26, 28 in the components 12, 14 and then into respective openings 30, 32 of the support plate 20.A · US 2020/0148523 A1 · ¶ 22
The directional drill includes a first gripper, including a first pair of gripping jaws located in a vice frame, at least one actuating device coupled to the first pair of gripping jaws, and a first common jaw pivot coupled to both jaws in the first pair of gripping jaws, the first common pivot coupled to the vice frame; wherein both jaws in the first pair of gripping jaws are constrained to only rotational motion about the first common jaw pivot.B · US 12,258,818 B2 · ¶ 38
An empty cell means only that no passage was reproduced there.
It would be desirable to provide a bottle neck gripper with improved design and strong performance.A · US 2020/0148523 A1 · ¶ 4
It is desirable to have a reliable system to add and remove segments of drill stem.B · US 12,258,818 B2 · ¶ 4
It is further desirable to reduce cost of the directional drill.B · US 12,258,818 B2 · ¶ 4
patent.fyi, US 2026/0356646 A1, claim 1, first published 2026-11-20T04:54:27-05:00, https://patent.fyi/US20260356646/, SHA-256 1dbad6b6673c932365e884307d58e89468074c842b7e4489a889c5a9095db905