1.1Side entry from a pump
A diaphragm pump draws liquid through a dip tube and sends it through a drilled side passage to the fill opening. The pump stops when liquid reaches an overflow port that returns excess liquid to the reservoir.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A diaphragm pump draws liquid through a dip tube and sends it through a drilled side passage to the fill opening. The pump stops when liquid reaches an overflow port that returns excess liquid to the reservoir.
An external bracket holds two compression springs that bear on pushrod collars. The rods pass through sealed guide bores and press the insert against the sliding plate.
Four linear bushings on the plate run on two parallel round rails fixed to external brackets. The rails set the plate height over a flat lower block with a circular discharge bore.
A blind pocket in the drum fills when its opening faces the feed port. The drum turns 180 degrees to empty the pocket through a discharge port below while its cylindrical surface closes the feed port.
A narrow annular land surrounds the feed bore in a one-piece upper block. An adjustable lower wear pad sets the clearance between the lapped land and the sliding plate to limit leakage during travel.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A nursery dispenser mounts a hopper of pelleted seed above the upper section and a discharge chute below the lower section. The plate slides in the lower slot and carries a through-pocket sized for one pellet, while the recessed spring-loaded insert bears against the plate around the hopper opening. At the fill position, the pocket sits under the hopper and the lower section supports the pellet. At the discharge position, the pocket aligns with the chute and the pellet drops into a tray cell.
A single conical disc spring supplies the insert preload. The disc spring sits in a circular counterbore at the back of the upper recess, centered on a guide boss on the insert. A shoulder in the recess limits inward travel before the spring flattens. The spring presses the insert against the plate as the plate moves through the lower slot.
A machined tin bronze insert fits into a rectangular recess above a hardened stainless steel plate. The underside of the insert has a flat sealing land around the feed opening, and the recess sidewalls keep the insert from turning. A compression spring bears on the back of the insert and holds the sealing land against the moving plate. Separating the upper and lower sections exposes the insert for replacement.
A 20 mm thick slide plate contains a straight 25.2 mm diameter through-pocket with a geometric volume of approximately 10 mL. The fill and discharge centers are 50 mm apart, and mechanical stops set the plate stroke to 50 mm. Contact faces above and below the plate close the pocket during transfer, and the spring-loaded insert seals around the fill opening. A low-viscosity liquid feeds by gravity, with a one-second dwell at each stop for filling and draining.
An indexing conveyor positions open containers directly below the discharge opening in the lower section. An electric linear actuator connects to the plate through a clevis, and the spring-loaded insert remains seated against the plate beneath the hopper. The conveyor controller starts the discharge stroke when the conveyor reports that it has stopped and a photoelectric sensor confirms that a container is present. A return-position switch confirms that the plate is back at the fill position before the conveyor advances.
A slide doser for opaque granules has a transparent window in the lower section directly beneath the fill position, with the window flush with the slot floor. A near-infrared reflectance sensor below the window measures the pocket contents while the recessed spring-loaded insert bears against the top of the plate. The controller compares the sensor signal against a threshold established from empty and filled pockets and requires a sustained filled reading before moving the plate to discharge. If the fill timer expires first, the controller holds the plate at the hopper and signals a feed fault.
A milled recess in the bottom surface contains two blind seats for stainless steel compression springs. The springs sit on opposite sides of the feed opening and press on the back of the insert.
A stainless steel lower block bolts to the upper section and contains a straight rectangular slot. Replaceable acetal strips line the slot floor and sidewalls and provide sliding surfaces for the plate.
A 5 mm thick stainless steel plate slides along the slot and carries an 8 mm diameter through-bore with a nominal volume of 0.25 mL. The bore fills under the feed opening while the slot floor closes its underside, then empties when the plate aligns it with the discharge opening.
A machined polyethylene insert fits in the recess and has a central opening aligned with the feed passage. Compression springs bear on its rear face and maintain contact between its flat sealing face and the moving plate.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Said device comprises a supply hopper, a metering chamber with a flange resting upon a bottom of the hopper, and a valve stem with an actuator.A · US 2018/0030605 A1 · ¶ 7
Clamps 44 hold strip 12a in a curved state (e.g., a flexed, bent state) in an absence of pressure in nip 11a. Similar to the pressure shoe in FIG. 1, outer surface 13a, when pressed against nip 11a, forms an entrance gap with mold roll 14.B · US 2021/0252750 A1 · ¶ 69
An empty cell means only that no passage was reproduced there.
The invention relates to nonferrous metallurgy, in particular to the electrolytic production of aluminum, namely to the devices for feeding electrolytic cells, and can be used to feed alumina, aluminum fluoride, crushed electrolyte to electrolytic cells for producing aluminum.A · US 2018/0030605 A1 · ¶ 1
These disadvantages impair the continuity of the feed supply and filling of the metering chamber.A · US 2018/0030605 A1 · ¶ 6
Improvements in the controlled thickness and uniformity of the base layer are sought, as well as improvements in roll-molding methods and in the equipment for performing such methods.B · US 2021/0252750 A1 · ¶ 2
In some examples, the outer surface of the pressure shoe is conformable such as to form a resin base with a substantially uniform thickness of less than 0.075 millimeters.B · US 2021/0252750 A1 · ¶ 5
patent.fyi, US 2026/0356650 A1, claim 1, first published 2026-11-20T04:54:27-05:00, https://patent.fyi/US20260356650/, SHA-256 3efbf8cec80d5fd6b985c03939a65f65d174e6da1ee39d655166b52137e4ea3e