1.1Open rail component support
A stainless steel rail spans two mounting brackets and carries the nozzle on a split clamp. Individual valve brackets and tubing clips secure the supply lines along the rail.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A stainless steel rail spans two mounting brackets and carries the nozzle on a split clamp. Individual valve brackets and tubing clips secure the supply lines along the rail.
A short cantilever arm holds the nozzle over the cup position. Flexible supply lines run from the dispenser valves to the nozzle, and a clamp on the arm takes up hose tension.
A mounting plate holds the two housings side by side above the cup. The first fluid exits through the nozzle housing, and the second fluid passes through the screen cartridge before exiting through a separate outlet angled toward the same point in the cup.
The first inlet feeds a header that distributes fluid to four axial bores drilled in the nozzle housing wall. The bores discharge around the central outlet, while the second fluid passes through the screens in the central chamber.
The first screen divides the inlet flow into small jets that spread and merge in the enlarged chamber. The greater cross-sectional area lowers the mean flow velocity, and a rounded outlet lip guides the flow into a single stream.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A textile finishing station mounts the nozzle above a trough that feeds a roller nip. The first inlet feeds rinse water through the gap between the outer housing and the inner cartridge, while the second inlet feeds an aqueous finishing solution through two stacked perforated screens in the cartridge. An angled injector at the outlet directs a wetting agent into the screened stream, and both streams discharge into the trough.
Two sintered stainless steel filter discs replace the perforated screens in the inner chamber. A spacer ring separates the discs, and perimeter gaskets seat each disc against a shoulder so that fluid from the second inlet passes through both porous faces in succession. The first fluid exits through the surrounding gap, and a side injector directs additive into the screened stream immediately below the downstream disc.
A 12 mm outside diameter cartridge fits inside a nozzle bore with a 13 mm inside diameter, forming a 0.5 mm radial gap for the first fluid. Three 8 mm diameter screens with 0.6 mm apertures on a 1 mm square pitch sit in the cartridge with 1 mm clear spacing between adjacent faces. The second inlet supplies the screen stack at 60 mL/min, and two opposed injector tips direct additive into the central stream 2 mm below the last screen.
Independent solenoid valves with closing times below 30 ms sit near the two nozzle inlets, and a separate metering valve sits next to the additive injector. A timer opens both inlet valves for a two-second dispense and opens the additive valve from 0.2 to 1.6 seconds into that interval. The angled injector directs the additive pulse into the screened central stream, and plain water continues through both the screened path and surrounding gap for the final 0.4 seconds to rinse their outlet surfaces.
A rotary bottle filler carries one nozzle above each bottle lift. Separate passages in a multichannel rotary union supply the first inlet, the second inlet, and the additive injector at each filling station. A rotary encoder triggers the inlet valves and additive metering valve after the lift positions a bottle beneath the nozzle. The surrounding gap and the screened central outlet discharge into the bottle as the injector directs additive into the central stream.
Inline flowmeters measure delivery in both inlet branches and in the additive line upstream of the injector. A controller sums the measured inlet flows, multiplies the total by a recipe ratio, and adjusts a proportional valve until the measured additive flow matches the resulting setpoint. The injector discharges into the central stream below the screen stack, and the controller closes the additive valve when both inlet flows fall below their configured thresholds.
A bent stainless steel cover encloses the valve bank and tubing, and a removable lower panel provides access to the connections. A reinforced flange transfers the nozzle load to the side panels.
A radial inlet bore through the nozzle housing wall joins the first supply line to the housing interior. A captured elastomer O-ring seals the push-in tube fitting.
Two woven stainless steel discs sit in the chamber with a 3 mm spacer ring between them. The downstream disc has smaller mesh openings, and a retaining ring holds the stack against a shoulder.
A diaphragm metering pump feeds additive through a check valve and a capillary with a 0.8 mm bore. The capillary points inward at 30 degrees to the axis of the second fluid stream and discharges just below its outlet.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As shown, beverage dispensing valve 100 may include a beverage dispensing nozzle 10, a housing 11, and an actuator 13 which may activate a beverage dispensing function of a beverage dispenser.B · US 2018/0282143 A1 · ¶ 59
A multiple flavor beverage mixing nozzle, comprising: a main body securable to a beverage dispensing device; an outer nozzle securable to the main body; an inlet cap securable to the main body, the inlet cap including an orifice therethrough; an inner body positioned below the inlet cap, whereby the inlet cap and the inner body define at least a portion of a mixing fluid channel coupled with a mixing fluid source and adapted to deliver a mixing fluid into the outer nozzle, fuA · US 2009/0230149 A1 · claim 37
In some embodiments, the valve includes a diffuser upstream of the nozzle shell configured to raise the pressure of the carbonated water such that it experiences a pressure drop when flowing into a nozzle shell chamber.B · US 2018/0282143 A1 · ¶ 7
From the flavor syrup fluid passageway 82, the flavor syrup exits under pressure through the angled nozzles 85, which are angled towards the longitudinal axis of the beverage dispensing nozzle 10.A · US 2009/0230149 A1 · ¶ 49
Syrup flowing through conduit 212 may exit baffle 103 through openings 213. In some embodiments, openings 213 may be inclined, such that they are mixed with the flow of carbonated water 209.B · US 2018/0282143 A1 · ¶ 50
An empty cell means only that no passage was reproduced there.
By using a single nozzle capable of dispensing multiple beverages to replace nozzles dispensing individual beverages, considerable space would be saved.A · US 2009/0230149 A1 · ¶ 8
A problem inherent in beverage dispensing devices using multiple flavor beverage mixing nozzles is cross-contamination/color carry-over.A · US 2009/0230149 A1 · ¶ 9
In particular, embodiments relate to beverage dispensing valve, as well as beverage dispensing nozzle systems and methods used in a beverage dispenser, in order to reduce carbonation in a finished beverage.B · US 2018/0282143 A1 · ¶ 1
Various systems and methods for carbonation reduction may be used.B · US 2018/0282143 A1 · ¶ 2
patent.fyi, US 2026/0356652 A1, claim 1, first published 2026-11-20T04:54:27-05:00, https://patent.fyi/US20260356652/, SHA-256 dfc80108b10e37d19bdcd1a1b9cb85999355cfc9848fcb08e183a948a2b0ebc8