1.1Open frame supports dispensing hardware
Clamps secure the containers to the upper rail, and mounting plates secure the pumps to the lower rail. Food-contact tubing connects each container to its pump and carries the product to the outlet.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Clamps secure the containers to the upper rail, and mounting plates secure the pumps to the lower rail. Food-contact tubing connects each container to its pump and carries the product to the outlet.
One pump draws from a single reservoir and feeds a tee with a solenoid valve on each branch. The controller opens the selected branch valve and runs the pump until a flowmeter registers the selected volume.
Vented containers feed separate downward-sloping tubes fitted with pinch valves. A load cell beneath the receiving cup measures the dispensed mass, and the controller closes the selected valve at the mass corresponding to the requested volume.
A rigid bracket holds each pump close to its container outlet, keeping the suction tube short. The discharge tubes pass through grommets into the second chamber and connect to the dispenser head.
A base plate secures the pedestal to the countertop above the receiving cup position. Flexible discharge tubes connect the pumps to the head, and strain relief at each end keeps tube loads off the fittings.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Two sealed containers of aqueous dye concentrate sit in the first chamber, and two peristaltic pumps sit in the second chamber. Each pump draws from one container and sends dye through a separate tube to the dispensing head attached to the second chamber. The head sits above a weighing vessel, and a controller stops each pump when the scale registers the selected mass increase for that dye.
Two vented reservoirs sit in the first chamber with their outlets above the dispensing head. Separate gravity feed lines run from the reservoirs to a motor-driven rotary plug valve in the second chamber in place of a pump. The valve connects one reservoir at a time to the head attached to the second chamber and blocks both lines in its closed position. A scale under the receiving cup signals the controller to close the valve at the selected dose mass.
The first chamber holds six 10-liter containers of flowable food, and the second chamber holds six variable-speed peristaltic pumps rated for 2 liters per minute each. Each pump draws from a dedicated container and feeds a separate tube terminating at the head attached to the second chamber. The controller dispenses portions of 0.5 to 3 liters using a stored volume-per-revolution calibration for each pump. The controller runs the selected pump at 2 liters per minute until the final 100 milliliters and then reduces the flow to 0.4 liters per minute.
The first chamber holds two 2-liter dairy containers on a refrigerated shelf maintained at 2 to 4 °C. Two peristaltic pumps sit in the second chamber and deliver portions of 20 to 100 milliliters through separate food-contact tubes. The tubes pass through a chilled aluminum block in the head attached to the second chamber, and a temperature sensor regulates coolant flow to maintain the block at 2 to 4 °C between portions. The controller runs the selected pump for the revolution count stored for the requested portion.
An indexing cup conveyor carries open cups beneath a dispensing head attached to the second chamber. Containers in the first chamber feed dedicated pumps in the second chamber through separate suction lines, and discharge lines carry the products to the head. At each stop, the conveyor controller signals that the cup is in position, and a photoelectric sensor confirms cup presence before dispensing begins. The dispenser controller signals completion after the selected doses finish, and the conveyor advances one position.
Two containers in the first chamber supply dedicated peristaltic pumps in the second chamber, and both discharge lines terminate at the head attached to the second chamber. A controller converts the selected volume to a target mass using a stored density for the selected product and tares the scale beneath the cup. The controller stops the pump near the target, waits for the scale reading to settle, and adds short pump pulses until the measured mass reaches the target tolerance. After each dose, the controller updates the stored mass per pump revolution from the measured mass and recorded revolution count.
A stainless steel partition divides the housing into an ingredient chamber above and a pump chamber below. A perimeter gasket seals the partition, and compression fittings carry the food lines through it.
Two flexible food pouches lie side by side in removable trays within the first chamber. A self-closing outlet fitting connects each pouch to its feed line, and the pouch collapses as product leaves.
A motor-driven roller pump in the second chamber compresses a flexible food-contact tube connected to its corresponding container. The controller counts rotor revolutions and applies a calibrated volume per revolution to set the portion.
A stainless steel bracket secures the dispenser head to the second chamber. Separate passages carry the products to individual outlet tips above the same cup position.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The apparatus can generally comprise a storage compartment, a filter compartment, and a pump compartment.B · US 2021/0268452 A1 · abstract
Additionally, the food dispensing apparatus 100 prevents oxidation and sugar carmelization by preventing air from entering the at least two inner shells and contacting the food component 116 to help maintain or increase shelf life and/or to help maintain flavor, taste, and consistency of the food component 116.A · US 8,348,107 B2 · ¶ 57
The outer shell 102 can comprise an air pump assembly 104 for pumping air into the chamber between the outer shell 102 and the inner shell 110. The additional air in the chamber between the outer shell 102 and the inner shell 110 creates a higher pressure and can dispense or decrease the amount of force necessary to dispense a food component 116 from inside the inner shell 110 through the nozzle 108.A · US 8,348,107 B2 · ¶ 48
A method for dispensing multiple food components 116 from a food dispensing apparatus 100 comprises placing food in an inner shell 110, placing the inner shell in an outer shell 102, coupling a nozzle 108 to the outer shell 102 for providing a dispensing nozzle, fastening the inner shell to the outer shell, utilizing a food selector located in the nozzle to choose at least one of multiple food components, supplying air to the chamber between the outer shell and the at least oA · US 8,348,107 B2 · ¶ 69
An empty cell means only that no passage was reproduced there.
However, food components stored in bottles can undergo serum separation, or syneresis.A · US 8,348,107 B2 · ¶ 3
Additionally, highly viscous food components are not easily dispensed from bottles or containers.A · US 8,348,107 B2 · ¶ 3
Further, another need exists for an apparatus and system for managing the level of dissolved gases in water for aquatic life comprising low-volume circulation techniques that can adequately degas or strip harmful dissolve gases from the water, such as ammonia, carbon dioxide, and the like.B · US 2021/0268452 A1 · ¶ 5
In even yet another embodiment, the modular aeration apparatus can also comprise a chilling compartment coupled with the storage compartment.B · US 2021/0268452 A1 · ¶ 7
patent.fyi, US 2026/0356656 A1, claim 1, first published 2026-11-20T04:54:27-05:00, https://patent.fyi/US20260356656/, SHA-256 9eea8ef6995f77965ac6061f8645a19a893b207a976ba97bd630d526a093078b