1.1Rigid link suspends foot contact
A clevis pin joins the upper end of a rigid aluminum link to a fitting on the girth. A stop at the clevis limits upward swing and transfers the rider’s upward force from the foot contact into the girth.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A clevis pin joins the upper end of a rigid aluminum link to a fitting on the girth. A stop at the clevis limits upward swing and transfers the rider’s upward force from the foot contact into the girth.
A rigid plate with a flat rubber facing spans the boot instep. The plate spreads the upward load across the contact area, and its open sides let the rider withdraw the boot laterally.
A bolted steel eye on the saddle tree captures a stitched loop at the upper end of the foot-contact strap. The tree transfers upward load into the saddle’s girth attachments, and the tightened girth holds the saddle down.
A horizontal webbing segment runs rearward along the saddle flap from a forward girth attachment. Its rear end carries an instep pad, and a guide fixed to the saddle tree takes the vertical reaction when the boot presses upward.
A vertical padded plate sits beside the outer edge of the boot. The plate limits outward drift during lateral motion, and the clear space above the boot lets the rider lift away.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rowing shell carries a transverse webbing band that passes behind the foot stretcher and bears against its side edges. A short strap runs from the band to a padded concave cup over the instep, while the shoe sole bears on the stretcher. Upward foot motion loads the cup and transfers tension through the band into the stretcher. The rower slides the foot rearward to withdraw it from beneath the cup.
A 6 mm sheathed polyester cord forms two parallel legs between an underside anchor band and a concave instep cup. Each cord leg passes through a separate rounded eye in the cup, and the proximal cord loop is captured in a sewn sleeve on the anchor band. Upward foot pressure tensions both legs, and the spaced eyes limit rotation of the cup about the direction of pull.
A shallow sealed bladder of thermoplastic polyurethane replaces the rigid concave foot-contact element. The bladder sits in a sewn fabric pocket with curved seams that place its lower face over the instep, and the distal strap is sewn across the upper face of the pocket. Welded baffles limit fluid movement between the center and the sides. Upward foot pressure redistributes the fluid within each chamber, and the pocket transfers the resulting load to the strap.
A single 110 mm long concave shell carries two 30 mm long elastomer pads arranged fore and aft with a 15 mm gap. Each pad follows the transverse curvature of the shell and projects 5 mm below its inner surface. The first strap joins the center of the shell, and upward foot pressure transfers through both pads into the shell and strap. The gap leaves a strip of the boot upper free of direct contact.
A conventional stirrup with a hinged tread hangs from the saddle and supports the sole of the boot. A separate strap rises from the underside anchor band and positions a concave cup above the instep, with the cup and tread staggered so the tread clears the cup throughout its swing. The tread transfers downward load to the saddle, and the cup transfers upward load to the anchor band. The tread pivots with changes in boot pitch.
A sealed strain gauge load cell sits in line with the first strap near its junction with the underside anchor band. A saddle-mounted logger samples the load cell at 100 Hz and converts its output to tension using a zero reading and a known calibration load. The logger records the start time, duration, and peak tension of each event that exceeds a set threshold for at least five consecutive samples. The cup transfers upward foot pressure through the instrumented strap into the anchor band.
Two vertical-axis rollers run along the boot sides just above the projecting outsole edges. When the boot rises, the outsole shoulders bear against the lower faces of the rollers, and an outward-opening arm lets the boot disengage.
A 25 mm leather strap folds around a steel loop on the girth and closes with a tongue buckle. The buckle engages holes on 15 mm centers to set the height of the distal foot contact.
A molded nylon shell has a concave underside that receives the top of the boot instep. A 3 mm rubber liner cushions contact, and rounded open edges let the boot slide out sideways.
A 75 mm polyester webbing girth passes beneath the horse and buckles to saddle billets on both sides. A reinforced loop sewn to the outer face of the girth receives the proximal end of the foot-contact strap.
A laminated leather distal segment is formed over a curved block so its centerline runs across the horse near the usual stirrup position. The curved end contacts the top of the boot and puts the strap in tension when the boot pushes upward.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In some embodiments, as shown in FIG. 5, the stirrup 12 is formed in an open shape which in this figure resembles an upside-down “L” shape, where the vertical element 26 is attached to the saddle 18, girth 22, or other strap 20, and the rider places his or her foot below the horizontal element 24.A · US 2015/0266716 A1 · ¶ 52
The stirrup 19 can have a stirrup coupler 21 attached to the foot loop portion 23 of the stirrup 19. The stirrup coupler 21 can be removably coupled to the coupling ring 15 or other coupling points 17 of the stirrup strap 11.B · US 2017/0267515 A1 · ¶ 22
An empty cell means only that no passage was reproduced there.
Such a system is therefore of only limited effectiveness when a rider is subjected to upward or sideward forces, for example when the horse is in a state of upset and bolts, bucks, or rears up.A · US 2015/0266716 A1 · ¶ 11
And novice riders, especially when learning how to jump obstacles on horseback, are highly susceptible to being thrown from the horse and may be in danger of serious injury thereby, because the horseback riding system they use provides little or no means to resist the associated upward and transverse forces in instances of rapid acceleration or deceleration.A · US 2015/0266716 A1 · ¶ 12
The primary source of difficulty arises from the construction of a conventional saddle, which has a high stirrup into which the rider must place their left foot, and then step up and swing their right leg over the rump of the horse.B · US 2017/0267515 A1 · ¶ 3
In one aspect, this disclosure is related to a secondary stirrup system for a saddle that allows an individual to safely and conveniently mount a saddle by providing them an easier route to the primary stirrup of the saddle.B · US 2017/0267515 A1 · ¶ 8
patent.fyi, US 2026/0356657 A1, claim 1, first published 2026-11-20T04:54:27-05:00, https://patent.fyi/US20260356657/, SHA-256 66a5cbad2a4279d11a583c302aa54f7a43ba3eda5db7ed749776edf060771e5f