1.1Open saddle with spring retention
A ceramic V-saddle sets the rod’s lateral position. An insulated leaf spring presses the rod into the saddle, and a flat stop sets its axial position.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A ceramic V-saddle sets the rod’s lateral position. An insulated leaf spring presses the rod into the saddle, and a flat stop sets its axial position.
The two spacers hold their apertures at the same radial distance and at azimuths 30 degrees apart. The bores follow the straight chord between the aperture centers, allowing a straight conductive rod to span the spacers at an angle to the centerline.
Compression bushings grip the cable jacket at each spacer, and light tension holds the cable along the treatment section. A controlled current through the strands produces a magnetic field around the cable, with the return lead routed away from the treatment section.
A motor turns a sealed rotor carrying a magnet with poles on opposite sides of its rotation axis. The changing pole orientation produces a periodic magnetic field in the fluid, and the rotor speed sets the field frequency.
An activated carbon bed removes free chlorine upstream of the treatment chamber. An insulated conductive rod carries current in the chamber and produces a magnetic field in the dechlorinated water as it flows past.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A chlorinated produce wash flume has a water-filled side pocket that communicates with the main channel through a slotted partition. Two spacers hold a single insulated conductive rod horizontally below the minimum water level, with both apertures at the same angular position about the module centerline. A low-voltage current supply drives the rod through sealed leads, and the magnetic field extends into the wash water in the pocket.
Two PEEK split bushings replace the fixed rod apertures in the end spacers. Each spacer has a radial slot that accepts one bushing, and the slots share the same angular position about the assembly centerline. The bushing halves close around the insulated conductive rod and slide into the slots, where retaining plates capture them during immersion. Sealed leads carry current through the rod to generate a magnetic field in the surrounding chlorinated water.
Two insulating spacers hold a single 8 mm diameter copper rod across a 150 mm span in a 20 L tank of chlorinated water. The spacer apertures share the same angular position, and a continuous fluoropolymer sleeve and sealed end connections isolate the copper from the water. A current-regulated driver supplies alternating 5 A pulses, with 10 ms on and 40 ms off, so the magnetic field reverses direction on successive pulses. The insulated return lead runs along the opposite wall of the tank.
A valved bypass takes chlorinated water downstream of a recirculating sand filter and returns it to the line upstream of the circulation pump. A vertical flooded chamber in the bypass contains a single insulated conductive rod held by two spacers with aligned apertures. Water enters below the lower spacer, flows through openings around the rod, and exits above the upper spacer. Sealed electrical feedthroughs connect the rod to a current supply outside the chamber.
Two spacers with aligned apertures hold a single insulated conductive rod below the surface of a chlorinated tank. A sealed Hall sensor mounts 15 mm from the rod axis at midspan, with its sensitive axis tangent to the magnetic field around the rod. A controller samples the sensor during each current pulse and subtracts the reading taken immediately before the pulse. It adjusts the next pulse amplitude toward a 50 µT field change, subject to a 5 A current limit.
Two spacers with aligned apertures suspend a single insulated conductive rod across a flooded inlet bay in a chlorine contact tank. A flowmeter on the inlet pipe sends a pulse to a controller for every 10 L of water entering the bay. The controller commands a 3 A, 100 ms rod current pulse on each meter pulse, and a level switch disables the current supply when the water drops below the rod assembly.
A pump circulates chlorinated water through a thin-walled polymer tube mounted parallel to the rod. Current through the rod produces a magnetic field that extends through the tube wall into the flowing water, and the rod-to-tube spacing sets the distance from the field source.
An alumina spacer contains a round through-bore lined with a fluoropolymer bushing. The bushing supports the first end of the conductive rod and protects its insulation from the ceramic bore edge.
Two circular polymer spacers slide onto a central support tube with an axial key. Each spacer has a rod bore at the same radial distance and angle relative to the key, which holds the bores in circumferential alignment.
A solid copper rod sits in bushings pressed into the two spacer apertures. A current-regulated supply sends rectangular current pulses through the rod, and the magnetic field around the rod follows the current waveform.
A continuous fluoropolymer jacket encloses the conductive rod below the operating waterline, and sealed feedthroughs connect it to dry terminals. The chlorinated water contacts the jacket, and the magnetic field from the current-carrying rod extends into the water.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The fuel rod spacer assembly 10 is organized in a rod supporting cell 15 which supports fuel rods 20 (shown in FIG. 3) as an array.A · US 2007/0291893 A1 · ¶ 22
In various embodiments, the first rod spacer comprises a fluid pipe aperture and at least one rod aperture, and the second rod spacer comprises a fluid pipe aperture and at least one rod aperture wherein the rod aperture of the first rod spacer and the rod aperture of the second rod spacer are circumferentially aligned about a centerline axis.B · US 2015/0344334 A1 · abstract
In various embodiments, the conductive rod comprises a first attachment portion and a second attachment portion, wherein the first attachment portion is disposed in the rod aperture of the first rod spacer, the second attachment portion is disposed in the rod aperture of the second rod spacer, and the conductive rod extends therebetween.B · US 2015/0344334 A1 · abstract
In various embodiments, an electromagnetic fluid treatment assembly may comprise one or more conductive rods disposed about a fluid pipe. Application of electrical current to the conductive rods may generate one or more magnetic fields that pass through the fluid pipe and any fluid disposed therein.B · US 2015/0344334 A1 · ¶ 19
An empty cell means only that no passage was reproduced there.
Consequently, a need exists for a fresh approach to the problem of debris capture in nuclear reactors.A · US 2007/0291893 A1 · ¶ 7
The fuel rod spacer assembly contains a guide for directing debris to open passages in a fuel rod spacer assembly.A · US 2007/0291893 A1 · ¶ 8
Hard water containing high levels of calcium, magnesium, and various other elements or minerals tends to form scale deposits on the inside surfaces of plumbing and other fluid circulation systems.B · US 2015/0344334 A1 · ¶ 3
In various embodiments, treatment of fluid with a generated magnetic field can minimize or prevent mineral scaling.B · US 2015/0344334 A1 · ¶ 5
patent.fyi, US 2026/0356707 A1, claim 1, first published 2026-11-20T06:11:26-05:00, https://patent.fyi/US20260356707/, SHA-256 d3829a62bce8dc49918e07eb6f3a8f128fab005879c2b6219242e7062a500657