1.1Wet aggregate charging
A twin-shaft mixer agitates the coarse and fine aggregates with part of the batch water. A weigh hopper meters cement into the moving wet aggregate bed, and the brine sludge slurry supplies the rest of the batch water.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A twin-shaft mixer agitates the coarse and fine aggregates with part of the batch water. A weigh hopper meters cement into the moving wet aggregate bed, and the brine sludge slurry supplies the rest of the batch water.
The mixer starts with part of the batch water, then receives coarse aggregate, fine aggregate, cement, and dewatered brine sludge through separate feeds. Mixer paddles break up the sludge cake and distribute the cement, and the water meter counts the moisture in the aggregate and sludge toward the batch-water total.
Washed sand passing a 4.75 mm sieve forms the granular skeleton. The cement and sludge slurry fills the voids between sand grains, and batch water is adjusted using a spread test to obtain a self-leveling fill.
Each cubic metre contains 45 kg of cement and 45 kg of sludge solids. A continuously graded aggregate blend limits the void volume, and a water-reducing admixture provides flow at a lower water dose. Trial batches establish the water and admixture doses using spread, bleed, and compressive strength measurements.
A kiln drives off bound water and carbon dioxide from the sludge solids. A controlled slaking step hydrates reactive lime before the powder enters the fill mixer. Loss on ignition is measured on the slaked powder, and trial batches establish the water demand and check hardened volume stability.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A batch mixer combines the dry aggregate and cement blend with the separately agitated brine sludge slurry. The mixer discharges into an agitated surge hopper that feeds a progressive cavity grout pump rated for the aggregate top size. A discharge hose carries the fill to the bottom of the placement zone, and the operator raises the outlet as the fill level rises.
Moisture probes at the aggregate bin outlets measure aggregate moisture, and a heated sample balance measures the solids fraction of the brine sludge. A batch controller uses these readings, aggregate absorption values, and load cell measurements to calculate the wet feed weights and the added water needed for the target effective water content. The controller meters the dry ingredients into the main mixer and the sludge and corrected water into a slurry tank before opening the slurry transfer valve.
A filter press removes free liquid from the sludge, and a low-temperature dryer produces solids that a mill breaks into powder. A screw feeder meters the powder into the dry blend, and a spray bar distributes batch water across the moving solids in the mixer.
A baffled tank receives metered batch water and dewatered brine sludge cake. A high-shear impeller breaks up the cake, and a recirculation pump keeps the solids suspended until the slurry transfers to the batch mixer.
Each cubic metre contains 1,125 kg of coarse aggregate and 375 kg of fine aggregate on a dry mass basis. The coarse fraction represents 0.75 of the combined aggregate mass.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
TABLE 9 Composition and results summary (commercial trial formula) Aggregate (g) Admixture Fine aggregate Coarse (g) Binder (g) Coarse aggregate Water Water A/C F/C W/C OPC SCM Glass sand 10 mm (g) reducer ratio ratio ratio 1 862.7 443.5 1526.3 530.9 234.0 2.6 2.9 4.23 0.27 1* 822 422 1453 505 223 2.5 2.9 4.23 0.27 2 827 711 1320 451 252.9 1.5 3 5.11 0.306 2* 790 679 1261 431 241.7 1.4 3 5.11 0.306 3 747.2 763.5 1417.8 435.9 234.0 1.5 3.5 5.67 0.313 3* 709 724 1345 414 222 1.B · US 2023/0159396 A1 · ¶
Refluxing—a) Mixture of lOg-50g of brine sludge, 50g-100g of fly ash, 6g-13g of sodium hydroxide, 250m1 - 500 ml of ethylene glycol, 1g-10 g of Cetyl trimethyl ammonium bromide and 12ml-26 ml of water is refluxed in a round bottom flask in the temperature range of 190 to 250 degree C. for the period of 2 - 6 hours, OR b) the above mixture is refluxed using microwave synthesizer in the temperature range of 40-45 degree C. for a duration of 15 - 20 minutes.A · US 2017/0057868 A1 · ¶ 26
The ratio of fine aggregates to coarse aggregates is 2 to 5 by weight and the dry density of formed paving blocks is 1800-2200 kg/m3.B · US 2023/0159396 A1 · ¶ 8
An empty cell means only that no passage was reproduced there.
The developed materials find application in areas such as radiation shielding materials, geopolymeric materials and chemically designed composites.A · US 2017/0057868 A1 · ¶ 3
Therefore, there is an urgent need to provide a process which converts toxic brine sludge waste into non-toxic form.A · US 2017/0057868 A1 · ¶ 7
Thus, there is a need in the art for improved compositions that have sufficient strength and reduced efflorescence.B · US 2023/0159396 A1 · ¶ 6
The present invention enhances the efflorescence resistance of concrete blocks through the use of glass powder in the concrete composition.B · US 2023/0159396 A1 · ¶ 7
patent.fyi, US 2026/0356758 A1, claim 1, first published 2026-11-20T06:49:46-05:00, https://patent.fyi/US20260356758/, SHA-256 dd9ac2092828e9055ecbca1a2a5d9eddc0435e6bb6ee83f46e7b7e2ee5ca56a6