1.1Waterborne starch binder
Corn starch is heated in water at 80 to 90 °C until the granules swell and form a paste. The paste is blended with wood flour, pressed into a panel, and dried so that solid starch bridges hold the particles together.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
Corn starch is heated in water at 80 to 90 °C until the granules swell and form a paste. The paste is blended with wood flour, pressed into a panel, and dried so that solid starch bridges hold the particles together.
A thin film of linseed oil and pine rosin binder is roll-coated onto the faces of dense cellulose sheets. The sheets are stacked and pressed, and the binder hardens at the interfaces to transfer shear between adjacent sheets.
Heat-bodied linseed oil and pine rosin are blended warm and cast in a shallow open mold. The exposed face cures in warm circulating air, and the strip is demolded to expose its second face for further oxidative hardening.
Dry ground limestone with a median particle size of 20 to 40 µm is blended into the warm linseed oil and resin binder. The particles pack into a rigid mineral phase while the binder wets their surfaces and hardens around them.
Hollow glass spheres are folded into the warm binder with a low-speed paddle to limit breakage. The spheres retain sealed gas cavities that lower panel density, and the hardened binder holds the spheres in place.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A binder of linseed oil and resin is mixed with chopped hemp fibers to form partitions for reusable instrument cases. A matched mold shapes the mixture into ribbed dividers with tabs along their lower edges. The dividers cure on open racks with air reaching both faces, and the tabs fit into slots in a removable case tray.
A linseed oil-modified long-oil alkyd resin replaces rosin in a binder that also contains linseed oil. The oil and alkyd are blended before dried hemp fibers are added incrementally in a paddle mixer. The mixture is spread into shallow open molds and cured under circulating air so oxygen reaches the exposed surface.
A linseed oil and resin binder is mixed with cork screened into fine particles of 0.25 to 0.50 mm and coarse particles of 1.0 to 2.0 mm. The two fractions are weighed at a fine-to-coarse mass ratio of 1 to 2. The fine fraction is dispersed in the binder first, then the coarse fraction is folded in at low speed. The blend is spread in a shallow mold and compacted against 4 mm stops.
A linseed oil and resin binder is mixed with short hemp fibers to form a facing for paper-faced gypsum board. A two-roll calender spreads the mixture onto a removable carrier, and the facing cures on ventilated racks. A roll laminator bonds the cured facing to the board with waterborne acrylic adhesive, and a rotary knife trims it flush with the board edges.
A linseed oil and resin binder is mixed with granulated cork and compacted into a thin infill layer in shallow molds. The layer cures on ventilated racks and is cut to fit steel trays used in pedestal-supported raised floors. Folded tray flanges retain the infill beneath a removable wear surface, and the steel tray bears on the pedestal heads.
A near-infrared sensor calibrated against gravimetric moisture measurements reads chopped hemp on the conveyor feeding a paddle mixer. A controller divides the target dry filler mass by the measured dry-mass fraction to calculate the feeder setpoint for each batch. Load cells verify the delivered filler mass, and a metering pump dispenses the linseed oil and resin binder in proportion to the target dry filler mass. The controller diverts filler when its moisture reading exceeds the range set for mixing.
Pine rosin is melted into heat-bodied linseed oil in a jacketed vessel. A paddle mixer incorporates dried wood flour in increments while the binder remains fluid enough to coat the particles.
Brewing trub containing hop particles is dewatered, dried, and milled through a 500 µm screen. The milled solids are blended into the warm binder until the particles are uniformly coated.
Flax fibers 2 to 4 mm long are dried and fed gradually into a paddle mixer containing the warm linseed oil and resin binder. The coated fibers are pressed into a sheet, where they bridge cracks in the cured binder.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
Preferably wood flour and/or cork flour in concentrations of 20-40 wt. % are used in the linoleum cement mixture.A · US 2006/0208237 A1 · ¶ 16
The first linoleum composition is produced by mixing the all components, such as the first linoleum cement, the first organic filler, and the first inorganic filler in a suitable mixing apparatus—e.g. a kneader, roll mill, or extruder, to form as homogenous a matrix as possible (mixed mass).B · US 2016/0101597 A1 · ¶ 54
According to a preferred embodiment the fire retarding linoleum cement composition contains a filler mainly consisting of cellulose. Examples of cellulose containing fillers are wood flour, cork flour and short cellulose containing natural fibres.A · US 2006/0208237 A1 · ¶ 14
In some embodiments, the first and/or second organic filler comprises a cellulosic material selected from wood fibers, cork, wood shavings, wood flour, paper fibers, cotton linters, a combination of two or more thereof.B · US 2016/0101597 A1 · ¶ 34
An empty cell means only that no passage was reproduced there.
When one now replaces completely the normal percentage of 20-30 wt % limestone through aluminium hydroxide, the fire proofing number unexpectedly raises to values>8 kW/m2.A · US 2006/0208237 A1 · ¶ 5
As aluminium hydroxide, as mentioned before, is relatively expensive, a part thereof can be replaced by calcium carbonate, as known from the before mentioned EP-0390647, which relates to a synergetic acting fireproofing addition of calcium carbonate and aluminium hydroxide to a totally different polymer mixture than a linoleum cement mixture.A · US 2006/0208237 A1 · ¶ 8
The present disclosure relates to surface coverings having improved dimensional stability.B · US 2016/0101597 A1 · ¶ 2
Thus, there remains a need for building panels that provide a combination of dimensional stability and acceptable aesthetics.B · US 2016/0101597 A1 · ¶ 4
patent.fyi, US 2026/0357040 A1, claim 1, first published 2026-11-20T09:31:44-05:00, https://patent.fyi/US20260357040/, SHA-256 2884395da30587fd4c13de1ca997a67f046dfb19ddddec2d62e2cde0415b23d5