Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
1.1Rupture force acceptance window
What ifWhat if capsule batches were accepted using an interval of measured rupture forces?
Claim language“Y=0.42X2−0.92X+T”
A microforce tester compresses individual capsules between parallel plates and records the force at the first abrupt load drop. The lower bound screens out capsules that rupture during handling, and the upper bound screens out capsules that resist the loads needed to release the oil.
1.2Diameter as the predictor
What ifWhat if the predictor of capsule modulus were the outer capsule diameter?
Claim language“X is the thickness of the capsule wall”
Optical images supply the outer diameters of capsules produced at a fixed shell-to-core feed ratio. Indentation measurements on representative capsules establish an empirical modulus curve for the diameter range of that capsule formulation.
1.3Modulus from plate compression
What ifWhat if capsule modulus were obtained by compressing whole capsules between flat plates?
Claim language“using a nano-indentation instrument”
A microforce tester records force and plate displacement during small, reversible compression of each capsule. A model of a liquid-filled spherical shell uses the measured radius and wall thickness to convert the initial force–displacement response into an apparent elastic modulus.
1.3Room temperature ion milling
What ifWhat if an ion beam opened a cross section through each capsule at room temperature?
Claim language“performing frozen section test on the microcapsule”
Cured epoxy supports the capsule while a focused ion beam mills toward its equatorial plane. A scanning electron micrograph of the exposed cross section supplies wall thickness measurements between the inner and outer boundaries.
Section 2 · machine-generated
Variations
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Other field of use
Crack repair in protective steel coatings
Disperse microcapsules containing a drying oil in an epoxy primer applied to steel. Set wall thickness and capsule modulus using Y = 0.42X² − 0.92X + T, where X is wall thickness in μm, Y is capsule modulus in GPa, and T is 0.9 to 1.1. A crack that intersects a capsule breaks its wall, and the released oil wets the crack and cures through oxidation in air.
Component substitution
Polyurea walls formed at droplet interfaces
Use a single polyurea wall around an asphalt rejuvenating oil core. Disperse the oil and an oil-soluble polyisocyanate as droplets in water, then add a water-soluble diamine to form polyurea at the droplet interfaces. Adjust the wall-forming reactant loading and qualify batches by nanoindentation and scanning electron microscopy of frozen sections, using the measured values to check the specified modulus–thickness relation.
Ion milling for capsule wall measurement
Use focused ion beam milling in place of frozen sectioning for wall thickness measurements. Mount intact microcapsules on a conductive support, apply a protective surface coating, and mill a cross-section through each capsule near its center. Image the exposed cross-section by scanning electron microscopy and measure the normal distance between the inner and outer wall boundaries at multiple positions. Measure modulus by nanoindentation on intact capsules from the same size fraction and use the two measurements to check the specified modulus–thickness relation.
Parameter or scale variation
Larger capsules for coarse asphalt mixtures
Size-classify oil-filled microcapsules to an outer diameter of 60–90 μm and set the wall thickness to 3–4 μm. At a wall thickness of 3 μm the specified modulus is 1.92–2.12 GPa, and at 4 μm it is 3.94–4.14 GPa. Check modulus by nanoindentation and wall thickness by scanning electron microscopy of frozen sections before blending the classified fraction into the asphalt mixture.
Combination with existing systems
Capsule addition during cold in-place recycling
Fit a dry-solids feeder to a cold in-place asphalt recycling train and meter rejuvenator-filled microcapsules into the pugmill downstream of the milling rotor. Add the capsules after the asphalt emulsion wets the reclaimed aggregate, and use the final mixing zone to distribute them before the mix is laid and compacted. Select batches by the specified modulus–thickness relation and check capsule survival in compacted trial sections. Capsules that intersect later cracks release rejuvenator into the surrounding binder.
Automated or data-driven variant
Automated screening of capsule production batches
Split each production sample into aliquots for automated nanoindentation and scanning electron microscopy of frozen sections. Use image segmentation to identify the inner and outer wall boundaries and calculate mean wall thickness for each capsule, then group the thickness and modulus measurements by batch and capsule diameter band. For each diameter band, calculate T = Y − 0.42X² + 0.92X from the group means and flag the batch for review when the value falls outside 0.9–1.1.
Specific version of a part
Quadratic modulus at two micrometers
At a wall thickness of 2.00 μm and a T value of 1.00, the quadratic relation gives a capsule modulus of 0.84 GPa. A batch of crosslinked polymer capsules is characterized by pairing wall thickness and modulus measurements.
Upper endpoint for T
The T setting is 1.10, the upper endpoint of the interval centered on 1.00. With X entered numerically in micrometers, this setting gives Y = 1.10 GPa at X = 0.00 μm as the fitted intercept.
Indentation and frozen section imaging
A diamond tip indents the apex of a supported capsule, and the unloading response supplies the capsule modulus in gigapascals. A cryomicrotome exposes a cross section of a frozen capsule, and a calibrated scanning electron micrograph supplies wall thickness in micrometers.
Cite aspatent.fyi, US 2026/0357068 A1, claim 1, first published 2026-11-20T10:10:52-05:00, https://patent.fyi/US20260357068/, SHA-256 97a842a2b4dedf99a4b432a48ed99eab6728246d33a8c3d82a21aed7b704cc9e